- 您现在的位置：买卖IC网 > PDF目录3798 > C8051F236-GQ (Silicon Laboratories Inc)IC 8051 MCU 8K FLASH 48TQFP PDF资料下载
参数资料
| 型号： | C8051F236-GQ |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 30/146页 |
| 文件大小： | 0K |
| 描述： | IC 8051 MCU 8K FLASH 48TQFP |
| 产品培训模块： | Serial Communication Overview |
| 标准包装： | 250 |
| 系列： | C8051F2xx |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 25MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 3.6 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-TQFP |
| 包装： | 托盘 |
| 产品目录页面： | 623 (CN2011-ZH PDF) |
| 其它名称： | 336-1244 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页
C8051F2xx
Rev. 1.6
125
17. Timers
The CIP-51 implements three, 16-bit counter/timers comparable with those found in the standard 8051
MCU's. These can be used to measure time intervals, count external events and generate periodic inter-
rupt requests. Timer 0 and Timer 1 are nearly identical and have four primary modes of operation. Timer
2 offers additional capabilities not available in Timers 0 and 1, such as capture and baud rate generation.
When functioning as a timer, the counter/timer registers are incremented on each clock tick. Clock ticks
are derived from the system clock divided by either one or twelve as specified by the Timer Clock Select
bits (T2M–T0M) in CKCON. The twelve-clocks-per-tick option provides compatibility with the older gener-
ation of the 8051 family. Applications that require a faster timer can use the one-clock-per-tick option.
When functioning as a counter, a counter/timer register is incremented on each high-to-low transition at the
selected input pin (P0.4/T0, P0.5/T1, or P0.6/T2. Events with a frequency of up to one-fourth the system
clock's frequency can be counted. The input signal need not be periodic, but it should be held at a given
level for at least two full system clock cycles to ensure the level is sampled.
17.1. Timer 0 and Timer 1
Timer 0 and Timer 1 are accessed and controlled through SFR's. Each counter/timer is implemented as a
16-bit register accessed as two separate bytes: a low byte (TL0 or TL1) and a high byte (TH0 or TH1). The
Counter/Timer Control (TCON) register is used to enable Timer 0 and Timer 1 as well as indicate their sta-
tus. Both counter/timers operate in one of four primary modes selected by setting the Mode Select bits
M1–M0 in the Counter/Timer Mode (TMOD) register. Each timer can be configured independently. Follow-
ing is a detailed description of each operating mode.
17.1.1. Mode 0: 13-bit Counter/Timer
Timer 0 and Timer 1 operate as a 13-bit counter/timer in Mode 0. The following describes the configuration
and operation of Timer 0. However, both timers operate identically and Timer 1 is configured in the same
manner as described for Timer 0.
The TH0 register holds the eight MSB's of the 13-bit counter/timer. TL0 holds the five LSBs in bit positions
TL0.4–TL0.0. The three upper bits of TL0 (TL0.7–TL0.5) are indeterminate and should be masked out or
ignored when reading. As the 13-bit timer register increments and overflows from 0x1FFF (all ones) to
0x0000, the timer overflow flag TF0 (TCON.5) is set and an interrupt will occur if enabled.
The C/T0 bit (TMOD.2) selects the counter/timer's clock source. Clearing C/T selects the system clock as
the input for the timer. When C/T0 is set to logic 1, high-to-low transitions at the selected input pin incre-
ment the timer register. (Refer to section 14 for information on selecting and configuring external I/O pins.)
Setting the TR0 bit (TCON.4) enables the timer when either GATE0 (TMOD.3) is 0 or the input signal /INT0
is logic-level one. Setting GATE0 to logic 1 allows the timer to be controlled by the external input signal
/INT0, facilitating pulse width measurements.
Timer 0 and Timer 1:
Timer 2:
13-bit counter/timer
16-bit counter/timer with auto-reload
16-bit counter/timer
16-bit counter/timer with capture
8-bit counter/timer with auto-reload
Baud rate generator
Two 8-bit counter/timers (Timer 0 only)
相关PDF资料 |
PDF描述 |
|---|---|
| USB-B-S-F-B-SM-R-TR | USB TYPE B 2.0 BLACK SMD |
| USB-A-S-F-W-SM2-R-TR | USB TYPE A WHITE SNGL SMD |
| USB-B-S-F-W-TH | USB TYPE B 2.0 WHITE T/H |
| P87C52X2BN,112 | IC 80C51 MCU 8K OTP 40-DIP |
| USB-B-S-F-B-TH-R | USB TYPE B 2.0 BLACK T/H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| C8051F236-GQR | 功能描述:8位微控制器 -MCU 8KB 1KRam 48Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F236R | 功能描述:8位微控制器 -MCU T-01280 Ram 48Pin RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F2XX | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Mixed Signal 8 kB ISP Flash MCU Family |
| C8051F300 | 功能描述:8位微控制器 -MCU 8KB 8ADC 2%osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F300DK | 功能描述:开发板和工具包 - 8051 MCU DEVELOPMENT KIT W/ US POWER SUPPLY RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。