参数资料
| 型号： | CAT25512YI-GT3 |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 512KB SPI SER 8-TSSOP |
| 标准包装： | 1 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 512K (64K x 8) |
| 速度： | 20MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 标准包装 |
| 其它名称： | CAT25512YI-GT3OSDKR |
CAT25512
Hold Operation
The HOLD input can be used to pause communication
between host and CAT25512. To pause, HOLD must be
taken low while SCK is low (Figure 11). During the hold
condition the device must remain selected (CS low). During
the pause, the data output pin (SO) is tri ? stated (high
impedance) and SI transitions are ignored. To resume
communication, HOLD must be taken high while SCK is low.
Design Considerations
The CAT25512 device incorporates Power ? On Reset
(POR) circuitry which protects the internal logic against
powering up in the wrong state. The device will power up
into Standby mode after V CC exceeds the POR trigger level
and will power down into Reset mode when V CC drops
below the POR trigger level. This bi ? directional POR
behavior protects the device against ‘brown ? out’ failure
following a temporary loss of power.
The CAT25512 device powers up in a write disable state
and in a low power standby mode. A WREN instruction
must be issued prior to any writes to the device.
After power up, the CS pin must be brought low to enter
a ready state and receive an instruction. After a successful
byte/page write or status register write, the device goes into
a write disable mode. The CS input must be set high after the
proper number of clock cycles to start the internal write
cycle. Access to the memory array during an internal write
cycle is ignored and programming is continued. Any invalid
op ? code will be ignored and the serial output pin (SO) will
remain in the high impedance state.
CS
SCK
HOLD
SO
Dashed Line = mode (1, 1)
t HD
t CD
t HZ
t HD
HIGH IMPEDANCE
Figure 11. HOLD Timing
http://onsemi.com
10
t CD
t LZ
相关PDF资料 |
PDF描述 |
|---|---|
| RBB108DHAD | CONN EDGECARD 216PS R/A .050 DIP |
| HSC49DRYI | CONN EDGECARD 98POS DIP .100 SLD |
| ASC50DRTN | CONN EDGECARD 100PS .100 DIP SLD |
| CAT25512VI-GT3 | IC EEPROM 512KB SPI SER 8-SOIC |
| ASC50DRTH | CONN EDGECARD 100PS .100 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT25-513JA | 功能描述:电阻器网络与阵列 51K 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
| CAT25-513JALF | 功能描述:电阻器网络与阵列 51K 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
| CAT25-560JA | 功能描述:电阻器网络与阵列 56ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
| CAT25-560JALF | 功能描述:电阻器网络与阵列 56ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
| CAT25-561JA | 功能描述:电阻器网络与阵列 560ohm 5% Concave 8resistors RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。