参数资料
| 型号： | CDB5461AU |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 19/44页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL & SOFTWARE CS5461A |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | CS5461A |
| 主要属性： | 1 相，能量至频率输出 |
| 次要属性： | GUI、USB、SPI、Microwire 接口 |
| 已供物品： | 板 |
| 产品目录页面： | 754 (CN2011-ZH PDF) |
| 相关产品： | CS5461A-ISZR-ND - IC ENERGY METERING 1PHASE 24SSOP 598-1095-5-ND - IC ENERGY METERING 1PHASE 24SSOP |
| 其它名称： | 598-1552 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
CS5461A
EXAMPLE #2:
The required number of pulses per unit energy present
on E1 is specified to be 500 pulses per kWhr, given that
the line voltage is 250 Vrms and the line current is
20 Arms. In such a situation, the stated line voltage and
current do not determine the appropriate PulseRateE 1,2
setting. To achieve full-scale readings in the instanta-
neous voltage and current registers, a 250 mV, DC-lev-
el signal is applied to the channel inputs.
sag level for more than half of the voltage sag duration
(see Figure 7 ).
To activate Voltage Sag detect, a voltage sag level must
be specified in the Voltage Sag Level Register
(VSAG Level ), and a voltage sag duration must be spec-
ified in the Voltage Sag Duration Register
(VSAG Duration ). The voltage sag level is specified as the
average of the absolute instantaneous voltage. Voltage
sag duration is specified in terms of ADC cycles.
PulseRateE 1 , 2 = ------------------------------ ? ---------------- ? ------------------- ? ------------------------- ? -------------------------
? 150mV ?
? 150mV ?
? 250V ?
? 20A ?
As in example #1, the voltage and current channel gains
are 10x, and the voltage level at the channel inputs will
be 150 mV rms when the levels on the power lines are
250 V rms and 20 A rms. In order to achieve
500 pulse-per-kW Hr per unit-energy, the
PulseRateE 1,2 Register setting is determined using the
following equation:
Level
500pulses 1Hr 1kW 250mV 250mV
kWHr 3600s 1000W
------------------- -------------------
Duration
Figure 7. Voltage Sag Detect
Therefor, the PulseRateE 1,2 Register is approximately
1.929 Hz. The PulseRateE 1,2 Register cannot be set to
a frequency of exactly 1.929 Hz. The closest setting is
0x00003E = 1.9375 Hz.
To improve the accuracy, either gain register can be
programmed to correct for the round-off error. This val-
ue would be calculated as
5.6 No Load Threshold
The CS5461A includes the LoadIntv (No Load Detec-
tion Interval) register and the LoadMin register to imple-
ment the no load threshold function. When the
accumulated energy measured within the time defined
by the LoadIntv register does not reach the value in the
-----------------------------------
Vgn or Ign
=
PulseRateE
1.929
? 1.00441 =
0x404830
LoadMin register, the pulse outputs will be disabled.
5.7 On-chip Temperature Sensor
If (MCLK/K) is not equal to 4.096 MHz, the
PulseRateE 1,2 Register must be scaled by a correction
factor of:
The on-chip temperature sensor is designed to assist in
characterizing the measurement element over a desired
temperature range. Once a temperature characteriza-
4.096MHz
----------------------------
(MCLK/K)
? PulseRateE1 , 2
tion is performed, the temperature sensor can then be
utilized to assist in compensating for temperature drift.
Therefore if (MCLK/K) = 3.05856 MHz the value of
PulseRateE 1,2 Register is
Temperature measurements are performed during con-
tinuous conversions and stored in the Temperature
Register . The Temperature Register (T) default is Cel-
4.096
PulseRateE
1 , 2
=
---------------------
3.05856
? 1.929Hz ? 2.583Hz
sius scale ( o C). The Temperature Gain Register (T gain )
and Temperature Offset Register (T off ) are constant val-
5.5 Voltage Sag-detect Feature
Status bit VSAG in the Status Register, indicates a volt-
age sag occurred in the power line voltage. For a volt-
age sag condition to be identified, the absolute value of
ues allowing for temperature scale conversions.
The temperature update rate is a function of the number
of ADC samples. With MCLK = 4.096 MHz and K = 1
the update rate is:
-----------------------------------------
the instantaneous voltage must be less than the voltage
DS661F3
2240 samples
(MCLK/K)/1024
=
0.56 sec
19
相关PDF资料 |
PDF描述 |
|---|---|
| CDB5466U | BOARD EVAL & SOFTWARE CS5466 ADC |
| CDB5467U | BOARD EVAL FOR CS5467 ADC |
| CDB5560-2 | DEV BOARD FOR CS5560 W/SE INPUT |
| CDB5571-2 | DEV BOARD FOR CS5571 W/SE INPUT |
| CDB8422 | BOARD EVAL FOR CS8422 RCVR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB5461AU-Z | 制造商:Cirrus Logic 功能描述:PB-FREEEVAL BOARD FOR CS5461 WITH USB - Bulk |
| CDB5462 | 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5462 - Bulk |
| CDB5463U | 功能描述:数据转换 IC 开发工具 Eval Bd Sngl-Phase Pow/Energy RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| CDB5463U-Z | 功能描述:EVAL BOARD USB FOR CS5463 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| CDB5464U | 功能描述:数据转换 IC 开发工具 Eval Bd 3-Ch Sngl-Phs Pow/Energy RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。