- 您现在的位置：买卖IC网 > PDF目录26505 > COM20019ILJP (STANDARD MICROSYSTEMS CORP) PDF资料下载
参数资料
| 型号： | COM20019ILJP |
| 厂商： | STANDARD MICROSYSTEMS CORP |
| 元件分类： | 微控制器/微处理器 |
| 中文描述： | 1 CHANNEL(S), 312.5K bps, LOCAL AREA NETWORK CONTROLLER, PQCC28 |
| 封装： | PLASTIC, LCC-28 |
| 文件页数： | 19/65页 |
| 文件大小： | 386K |
| 代理商： | COM20019ILJP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页
Cost Competitive ARCNET (ANSI 878.1) Controller with 2K x 8 On-Chip RAM
Rev. 09-25-07
Page 26
SMSC COM20019I
DATASHEET
6.2.7
Diagnostic Status Register
The Diagnostic Status Register contains seven read-only bits which help the user troubleshoot the network
or node operation. Various combinations of these bits and the TXEN bit of the Configuration Register
represent different situations. All of these bits, except the Excessive NAcK bit and the New Next ID bit, are
reset to logic "0" upon reading the Diagnostic Status Register or upon software or hardware reset. The
EXCNAK bit is reset by the "POR Clear Flags" command or upon software or hardware reset.
The
Diagnostic Status Register defaults to the value 0000 000X upon either hardware or software reset.
6.2.8
Command Register
Execution of commands are initiated by performing microcontroller writes to this register.
Any
combinations of written data other than those listed in Table 5 are not permitted and may result in incorrect
chip and/or network operation.
6.2.9
Address Pointer Registers
These read/write registers are each 8-bits wide and are used for addressing the internal RAM. New pointer
addresses should be written by first writing to the High Register and then writing to the Low Register
because writing to the Low Register loads the address. The contents of the Address Pointer High and Low
Registers are undefined upon hardware reset. Writing to Address Pointer low loads the address.
6.2.10 Configuration Register
The Configuration Register is a read/write register which is used to configure the different modes of the
COM20019I.
The Configuration Register defaults to the value 0001 1000 upon hardware reset only.
SUBAD0 and SUBAD1 point to the selection in Register 7.
6.2.11 Sub-Address Register
The sub-address register is new to the COM20019I, previously a reserved register. Bits 2, 1 and 0 are
used to select one of the registers assigned to address 7h. SUBAD1 and SUBAD0 already exist in the
Configuration register on the COM20020B. They are exactly same as those in the Sub-Address register. If
the SUBAD1 and SUBAD0 bits in the Configuration register are changed, the SUBAD1and SUBAD0 in
the Sub-Address register are also changed. SUBAD2 is a new sub-address bit. It is used to access the 1
new Set Up register, SETUP2. This register is selected by setting SUBAD2=1. The SUBAD2 bit is cleared
automatically by writing the Configuration register.
6.2.12 Setup 1 Register
The Setup 1 Register is a read/write 8-bit register accessed when the Sub Address Bits are set up
accordingly (see the bit definitions of the Configuration Register). The Setup 1 Register allows the user to
change the network speed (data rate) or the arbitration speed independently, invoke the Receive All
feature and change the nPULSE1 driver type. The data rate may be slowed to 156.25Kbps and/or the
arbitration speed may be slowed by a factor of two. The Setup 1 Register defaults to the value 0000 0000
upon hardware reset only.
相关PDF资料 |
PDF描述 |
|---|---|
| CP0603A2442CSTR | |
| CP0805A0881ESTR | |
| CP0805A1441BSTR | |
| CP2101-GMR | |
| CP2101 | |
相关代理商/技术参数 |
参数描述 |
|---|---|
| COM20019I-LJP | 制造商:SMSC 制造商全称:SMSC 功能描述:Low Cost ARCNET(ANSI 878.1) Controller with 2k X 8 On-Board RAM |
| COM20019ILJP3V | 功能描述:网络控制器与处理器 IC ARCNET Contrllr RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| COM20019ILJPTR | 功能描述:网络控制器与处理器 IC Arcnet (ANSI 878.1) Controllr 2k x 8 Ram RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| COM20019IP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| COM20020 | 制造商:SMSC 制造商全称:SMSC 功能描述:COM20020 3.3V ULANC Universal Local Area Network Controller with 2K x 8 On-Board RAM |
发布紧急采购，3分钟左右您将得到回复。