- 您现在的位置：买卖IC网 > Datasheet目录319 > CS5463-IS (Cirrus Logic Inc)IC PWR/ENERGY METER 2CH 24-SSOP Datasheet资料下载
参数资料
| 型号： | CS5463-IS |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 19/46页 |
| 文件大小： | 0K |
| 描述： | IC PWR/ENERGY METER 2CH 24-SSOP |
| 标准包装： | 59 |
| 输入阻抗： | 30 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 0.8V |
| 电压 - 低输入/输出： | 0.2V |
| 电流 - 电源： | 2.9mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
| 配用： | 598-1553-ND - BOARD EVAL & SOFTWARE CS5463 ADC |
| 其它名称： | 598-1192-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
CS5463
Output p in E3 is high when the line voltage is positive
and pin E3 is low when the line voltage is negative.
5.5.5 PFMON Output Mode
Setting bit E3MODE[1:0] = 1 (01b) in the Operational
Mode Register outputs the state of the PFMON compar-
ator on pin E3. Figure 8 illustrates the output format with
PFMON on E3
5.6 Sag and Fault Detect Feature
Status bit VSAG and IFAULT in the Status Register, in-
dicates a sag occurred in the power line voltage and
current, respectively. For a sag condition to be identi-
fied, the absolute value of the instantaneous voltage or
current must be less than the sag level for more than
half of the sag duration (see Figure 9).
To activate voltage sag detection, a voltage sag level
E1
E2
E3
Above PFMON Threshold
Below PFMON Threshold
must be specified in the Voltage Sag Level Register
(VSAG Level ), and a voltage sag duration must be spec-
ified in the Voltage Sag Duration Register (VSAG Dura-
tion ). To activate current fault detection, a current sag
FREQ P ? VREFIN
VIN ? VGAIN ? IIN ? IGAIN ? PF
100 ? 2.5
0.132 ? 10 ? 0.1125 ? 10
Figure 8. PFMON output to pin E3
When PFMON is greater then the threshold, pin E3 is
high and when PFMON is less than the threshold pin E3
is low.
5.5.6 Design Example
EXAMPLE #1:
The maximum rated levels for a power line meter are
250 V rms and 20 A rms. The required number of puls-
es-per-second on E1 is 100 pulses per second
(100 Hz), when the levels on the power line are
220 V rms and 15 A rms.
With a 10x gain on the voltage and current channel the
maximum input signal is 250 mV P . (See Section 5.1 An-
alog Inputs on page 16.) To prevent over-driving the
channel inputs, the maximum rated rms input levels will
register 0.6 in V RMS and I RMS by design. Therefore the
voltage level at the channel inputs will be 150 mV rms
when the maximum rated levels on the power lines are
250 V rms and 20 A rms.
Solving for PulseRate using the transfer function:
2
PulseRate = ---------------------------------------------------------------------------------------------
Therefore with PF = 1 and:
VIN = 220V ? ? ? 150mV ? ? ? 250V ? ? = 132mV
IIN = 15A ? ? ? 150mV ? ? ? 20A ? ? = 112.5mV
the pulse rate is:
2
PulseRate = ----------------------------------------------------------------- = 420.8754Hz
and the PulseRateE Register is set to:
level must be specified in the Current Fault Level Reg-
ister (ISAG Level ), and a current sag duration must be
specified in the Current Fault Duration Register (ISAG-
Duration ). The voltage and current sag levels are speci-
fied as the average of the absolute instantaneous
voltage and current, respectively. Voltage and current
sag duration is specified in terms of ADC cycles.
Level
Duration
Figure 9. Sag and Fault Detect
5.7 No Load Threshold
The No Load Threshold register (Load Min ) is used to
disable the active energy pulse output when the magni-
tude of the P Active register is less than the value in the
Load Min register.
5.8 On-chip Temperature Sensor
The on-chip temperature sensor is designed to assist in
characterizing the measurement element over a desired
temperature range. Once a temperature characteriza-
tion is performed, the temperature sensor can then be
utilized to assist in compensating for temperature drift.
Temperature measurements are performed during con-
----------------------------------------
PulseRateE =
PulseRate
? MCLK ? K ? ? 2048
=
0.2104377
tinuous conversions and stored in the Temperature
Register . The Temperature Register (T) default is Cel-
with MCLK = 4.096 MHz and K = 1.
DS678F3
sius scale (°C). The Temperature Gain Register (T gain )
and Temperature Offset Register (T off ) are constant val-
ues allowing for temperature scale conversions.
19
相关PDF资料 |
PDF描述 |
|---|---|
| CS5464-IS | IC PWR/ENERGY METER 3CH 28-SSOP |
| CS5466-ISZR | IC ENERGY METERING 1PHASE 24SSOP |
| CS5466-IS | IC ENERGY METERING 1PHASE 24SSOP |
| CS8312YN8 | IC PREDRIVER IGBT IGNITION 8DIP |
| CX1006 | SOCKET ADAPTER 40TSOP SUPERPRO5K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS5463-ISZ | 功能描述:电流和电力监控器、调节器 Single Phase Power/Energy IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| CS5463-ISZ/D | 制造商:Cirrus Logic 功能描述: |
| CS5463-ISZR | 功能描述:电流和电力监控器、调节器 IC Single Phase PWR/Energy RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| CS5463-ISZR/E2 | 制造商:Cirrus Logic 功能描述: |
| CS5464 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Three-channel, Single-phase Power/Energy IC |
发布紧急采购，3分钟左右您将得到回复。