参数资料
型号: CS5463-IS
厂商: Cirrus Logic Inc
文件页数: 37/46页
文件大小: 0K
描述: IC PWR/ENERGY METER 2CH 24-SSOP
标准包装: 59
输入阻抗: 30 千欧
测量误差: 0.1%
电压 - 高输入/输出: 0.8V
电压 - 低输入/输出: 0.2V
电流 - 电源: 2.9mA
电源电压: 4.75 V ~ 5.25 V
测量仪表类型: 单相
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 24-SSOP(0.209",5.30mm 宽)
供应商设备封装: 24-SSOP
包装: 管件
配用: 598-1553-ND - BOARD EVAL & SOFTWARE CS5463 ADC
其它名称: 598-1192-5
CS5463
7. SYSTEM CALIBRATION
7.1 Channel Offset and Gain Calibration
The CS5463 provides digital DC offset and gain com-
pensation that can be applied to the instantaneous volt-
age and current measurements, and AC offset
compensation to the voltage and current RMS calcula-
tions.
Since the voltage and current channels have indepen-
dent offset and gain registers, system offset and/or
gain can be performed on either channel without the
calibration results from one channel affecting the oth-
er.
The computational flow of the calibration sequences are
illustrated in Figure 12. The flow applies to both the volt-
N + 30 conversion cycles to complete. For AC offset cal-
ibrations, the sequence takes at least 6N + 30 ADC cy-
cles to complete, (about 6 computation cycles). As N is
increased, the accuracy of calibration results will in-
crease.
7.1.2 Offset Calibration Sequence
For DC and AC offset calibrations, the VIN ? pins of the
voltage and IIN ? pins of the current channels should be
connected to their ground reference level. (see Figure
13.)
External
Connections
age channel and current channel.
7.1.1 Calibration Sequence
0V +-
AIN+
+
XGAIN
+
The CS5463 must be operating in its active state and
ready to accept valid commands. Refer to Section 5.16
CM +-
AIN-
-
-
Commands on page 23. The calibration algorithms are
dependent on the value N in the Cycle Count Register
(see Figure 12). Upon completion, the results of the cal-
ibration are available in their corresponding register.
The DRDY bit in the Status Register will be set. If the
DRDY bit is to be output on the INT pin, then DRDY bit
in the Mask Register must be set. The initial values in
the AC gain and offset registers do affect the results of
the calibration results.
7.1.1.1 Duration of Calibration Sequence
The value of the Cycle Count Register (N) determines
the number of conversions performed by the CS5463
during a given calibration sequence. For DC offset and
gain calibrations, the calibration sequence takes at least
Figure 13. System Calibration of Offset
The AC offset registers must be set to the default
(0x000000).
7.1.2.1 DC Offset Calibration Sequence
Channel gain should be set to 1.0 when performing DC
offset calibration. Initiate a DC offset calibration. The DC
offset registers are updated with the negative of the av-
erage of the instantaneous samples collected over a
computational cycle. Upon completion of the DC offset
calibration the DC offset is stored in the corresponding
DC offset register. The DC offset value will be added to
to V*, I* Registers
?
In
Modulator
Filter
+
+
+
X
X
N
? N
?
+
+
+
V RMS *, I RMS *
Registers
?
DC Offset*
Gain*
N
AC Offset*
-1
X
Inverse
? N
-1
X
0.6
RMS
* Denotes readable/writable register
Figure 12. Calibration Data Flow
DS678F3
37
相关PDF资料
PDF描述
CS5464-IS IC PWR/ENERGY METER 3CH 28-SSOP
CS5466-ISZR IC ENERGY METERING 1PHASE 24SSOP
CS5466-IS IC ENERGY METERING 1PHASE 24SSOP
CS8312YN8 IC PREDRIVER IGBT IGNITION 8DIP
CX1006 SOCKET ADAPTER 40TSOP SUPERPRO5K
相关代理商/技术参数
参数描述
CS5463-ISZ 功能描述:电流和电力监控器、调节器 Single Phase Power/Energy IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
CS5463-ISZ/D 制造商:Cirrus Logic 功能描述:
CS5463-ISZR 功能描述:电流和电力监控器、调节器 IC Single Phase PWR/Energy RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
CS5463-ISZR/E2 制造商:Cirrus Logic 功能描述:
CS5464 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Three-channel, Single-phase Power/Energy IC