参数资料
型号: CS5463-IS
厂商: Cirrus Logic Inc
文件页数: 40/46页
文件大小: 0K
描述: IC PWR/ENERGY METER 2CH 24-SSOP
标准包装: 59
输入阻抗: 30 千欧
测量误差: 0.1%
电压 - 高输入/输出: 0.8V
电压 - 低输入/输出: 0.2V
电流 - 电源: 2.9mA
电源电压: 4.75 V ~ 5.25 V
测量仪表类型: 单相
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 24-SSOP(0.209",5.30mm 宽)
供应商设备封装: 24-SSOP
包装: 管件
配用: 598-1553-ND - BOARD EVAL & SOFTWARE CS5463 ADC
其它名称: 598-1192-5
CS5463
8. AUTO-BOOT MODE USING E 2 PROM
When the CS5463 MODE pin is asserted (logic 1), the
CS5463 auto-boot mode is enabled. In auto-boot mode,
the CS5463 downloads the required commands and
register data from an external serial E 2 PROM, allowing
the CS5463 to begin performing energy measurements.
8.1 Auto-boot Configuration
A typical auto-boot serial connection between the
CS5463 and a E 2 PROM is illustrated in Figure 17. In au-
to-boot mode, the CS5463’s CS and SCLK are config-
ured as outputs. The CS5463 asserts CS (logic 0),
provides a clock on SCLK, and sends a read command
to the E 2 PROM on SDO. The CS5463 reads the us-
er-specified commands and register data presented on
the SDI pin. The E 2 PROM’s programmed data is utilized
by the CS5463 to change the designated registers’ de-
fault values and begin registering energy.
commands/data will determine the CS5463’s exact op-
eration, when the auto-boot initialization sequence is
running. Any of the valid commands can be used.
8.2 Auto-boot Data for E 2 PROM
Below is an example code set for an auto-boot se-
quence. This code is written into the E 2 PROM by the us-
er. The serial data for such a sequence is shown below
in single-byte hexidecimal notation:
- 64 00 00 60
Write Operation Mode Register, turn high-pass
filters on.
- 44 7F C4 A9
Write value of 0x7FC4A9 to Current Gain
Register.
- 48 FF B2 53
Write value of 0xFFB253 to Voltage Gain
Register.
5K
V D +
EOUT1
EOUT2
CS5463
SCLK
Mech. Counter
or
Stepper Motor
EEPROM
SCK
- 74 00 00 04
Unmask bit #2 (LSD) in the Mask Register.
- E8
Start continuous conversions
- 78 00 01 00
SDI
SO
Write STOP bit to Control Register, to terminate
MODE
SDO
CS
5K
SI
CS
auto-boot initialization sequence.
8.3 Which E 2 PROMs Can Be Used?
Several industry-standard serial E 2 PROMs that will suc-
cessfully run auto-boot with the CS5461A are listed be-
Connector to Calibrator
low:
Figure 17. Typical Interface of E 2 PROM to CS5463
?
?
Atmel AT25010, AT25020 or AT25040
National Semiconductor NM25C040M8 or NM25020M8
Figure 17 also shows the external connections that
would be made to a calibrator device, such as a PC or
custom calibration board. When the metering system is
installed, the calibrator would be used to control calibra-
tion and/or to program user-specified commands and
calibration values into the E 2 PROM. The user-specified
40
? Xicor X25040SI
These types of serial E 2 PROMs expect a specific 8-bit
command (00000011) in order to perform a memory
read. The CS5461A has been hardware programmed to
transmit this 8-bit command to the E 2 PROM at the be-
ginning of the auto-boot sequence.
DS678F3
相关PDF资料
PDF描述
CS5464-IS IC PWR/ENERGY METER 3CH 28-SSOP
CS5466-ISZR IC ENERGY METERING 1PHASE 24SSOP
CS5466-IS IC ENERGY METERING 1PHASE 24SSOP
CS8312YN8 IC PREDRIVER IGBT IGNITION 8DIP
CX1006 SOCKET ADAPTER 40TSOP SUPERPRO5K
相关代理商/技术参数
参数描述
CS5463-ISZ 功能描述:电流和电力监控器、调节器 Single Phase Power/Energy IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
CS5463-ISZ/D 制造商:Cirrus Logic 功能描述:
CS5463-ISZR 功能描述:电流和电力监控器、调节器 IC Single Phase PWR/Energy RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
CS5463-ISZR/E2 制造商:Cirrus Logic 功能描述:
CS5464 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Three-channel, Single-phase Power/Energy IC