- 您现在的位置：买卖IC网 > PDF目录16686 > DC1029A (Linear Technology)EVAL BOARD FOR LTC2928 PDF资料下载
参数资料
| 型号： | DC1029A |
| 厂商： | Linear Technology |
| 文件页数： | 21/32页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR LTC2928 |
| 设计资源： | DC1029A Design File DC1029A Schematic |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电源监控器/跟踪器/序列发生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LTC2928 |
| 主要属性： | 4 通道电源定序器 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC2928
APPLICATIO S I FOR ATIO
Forcing Supplies Off or Disabling Unused Channels
The most convenient way to mask an unused channel is
to tie its respective RT input to ground. After sequenc-
ing begins, any enable output (EN) may be pulled low
permanently by driving the respective RT input to ground
(asynchronous OFF command). An asynchronously OFF
channel cannot be re-enabled until a new sequence-up
procedure is started. Any channel that is asynchronously
OFF is removed from participation in the sequencing and
supply monitoring processes, allowing the LTC2928 to
operate normally on the remaining operating channels.
When experiencing a fault in the “No Shutdown Debug
Mode”, the asynchronous OFF feature may be used to
conveniently pull down the enable outputs. Alternatively,
V CC may be turned off and on again. Clearing a fault con-
dition requires the ON input to be low while the supplies
are below their sequence-down thresholds.
Forcing Supplies On Prior to Sequencing
Prior to sequencing, any or all enable pins may be forced
high by pulling the respective RT pin to V CC . In this man-
ner, supplies may be tested individually or together in any
combination. With any RT pin at V CC , the respective voltage
monitor inputs and comparator outputs become active with
thresholds parked at the configured sequence-up thresh-
old. Outside of sequencing, RST (with 100% thresholds
selected) and OV are always functional, regardless of
RT pin state. If all four RT pins are at V CC , the LTC2928
can be used as a stand-alone quad voltage monitor with
under- and overvoltage indication as shown in Figure 11
(100% thresholds). With ON low in the RT forcing mode,
sequence, command and reset faults do not occur. External
faults however, may be detected (overvoltage, for example).
Any previously logged faults remain in memory and their
reporting will return upon exiting the forcing mode.
2.5V
V CC
SUPPLY
BANK
1.5V
1.8V
3.3V
LTC2928
52.3k
23.7k
17.8k
36.5k
EN1
EN2
EN3
EN4
RT1
V1
V2
V3
V4
HV CC
RT2
RT3
RT4
MS1
MS2
VSEL
10k
10k
10k
10k
CMP1
CMP2
CMP3
CMP4
V CC
GND
RTMR
PTMR
STMR
REF
0.047 F
0.1 F
SQT2
OVA
SQT1
CAS
RDIS
ON
RST
OV
FLT
DONE
SYSTEM
LOGIC
3.32k
10k
10k
2928 TA05
Figure 11. Quad Supervisor (No Sequencing)
2928f
21
相关PDF资料 |
PDF描述 |
|---|---|
| H3CCS-2036G | IDC CABLE - HKC20S/AE20G/HKC20S |
| ZXRE1004FRSTOB | IC VREF SHUNT PREC 1.22V TO-92-3 |
| V110B3V3E100B2 | CONVERTER MOD DC/DC 3.3V 100W |
| ELC-06D101E | COIL CHOKE 100UH RADIAL |
| RS3-4805DZ/H3 | CONV DC/DC 3W 20-60VIN +/-05VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1029A | 制造商:Linear Technology 功能描述:EVAL BOARD, LTC2928 QUAD POWER SUPPLY SE |
| DC102F2K | 制造商:U S SENSOR 功能描述:thermistor |
| DC102K | 制造商:RAYTHN 功能描述: |
| DC102R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DC-102R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:1.8watt 24pins DIP/DIL |
发布紧急采购，3分钟左右您将得到回复。