- 您现在的位置：买卖IC网 > PDF目录16686 > DC1029A (Linear Technology)EVAL BOARD FOR LTC2928 PDF资料下载
参数资料
| 型号： | DC1029A |
| 厂商： | Linear Technology |
| 文件页数： | 26/32页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR LTC2928 |
| 设计资源： | DC1029A Design File DC1029A Schematic |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电源监控器/跟踪器/序列发生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LTC2928 |
| 主要属性： | 4 通道电源定序器 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页
LTC2928
APPLICATIO S I FOR ATIO
2) Sequence-Up Phase
Start the sequence-up phase by transitioning the ON input
above 1V. At this point, the LTC2928 senses the sequence
position resistors on inputs RT1 through RT4. The sequence
timer is operating and the CAS pin pulls low at the start
of each time position. The CMP outputs are low during
sequencing unless a fault has occurred.
Protect shutdown inputs on regulators that are sensitive
to high voltage. In this application, the FPGA regulators
have their shutdown inputs connected to the 3.3V supply
through a 10k resistor, thereby limiting the pull-up voltage
on the shutdown inputs (the EN outputs alone may attempt
to pull-up as high as 9.3V (V CC + 6V).
DONE pulls low when all time positions are clocked through
(CAS has completed pulling low 8 times). The compara-
tor outputs become active and are allowed to pull high if
the supply monitor inputs are above their under-voltage
threshold.
The RST output pulls high after all the supplies have
remained above their undervoltage threshold for ap-
proximately 190ms. After RST is allowed to pull high, the
LTC2928 enters its supply-monitor phase. The LTC2928
RST pin pulls up to 3.3V. The schottky diode SD1 and
resistor RP1 limit the pull-up voltage at the FPGA reset pin.
Overvoltage Indication
If any positive supply monitor input exceeds its overvoltage
threshold at any time, OV pulls low. OV returns high once
all positive supplies are below their overvoltage threshold
for a period equal to the RST delay time. To shutdown all
supplies upon overvoltage, tie the OV output to FLT .
Overvoltage Threshold Adjustment
Use the OVA input to set the overvoltage threshold for
all positive supplies. Leave the OVA input open to set the
OV threshold at the supply monitor inputs to 32% above
the undervoltage threshold (V OVA = 0.660V). Ground the
OVA input to set the OV threshold to 12% above the un-
dervolatge threshold (V OVA ) = 0.556V). Tie the OVA input
to V CC = 3.3V to set the OV threshold to 115% above the
undervoltage threshold (V OVA = 1.072V). Select accurate
OV thresholds between 0.556V and 0.660V by connecting
and external resistor between OVA and ground (Figure 16).
Configure higher OV thresholds by connecting an external
resistor between OVA and V CC (Figure 17). These higher
thresholds are potentially less accurate due to variations
in V CC .
0.66 32
0.64 28
3) Supply Monitor Phase
0.62
24
V CC = 3.5V
V CC = 3V
Duringthesupply-monitorphase,ifanyofthefoursup-
plies drops below its selected threshold, RST pulls low.
Since this application considers an under-voltage condition
during the supply-monitor phase to be a reset fault, FLT
pulls low. All enable outputs pull low and the pass transis-
tors shut off. Because of the fault condition, the LTC2928
is prevented from re-sequencing until all supplies drop
below their sequence-down threshold, and the ON input
is below 0.97V.
4) Sequence-Down Phase
Begin the sequence-down phase by pulling the ON input
below 0.97V. RST and all CMP outputs pull low as soon as
the sequence-down command is detected. Beginning with
supplies in time position 8, the supplies are sequenced-
down reverse of the order in which they came up. At the
end of the sequence-down phase, DONE pulls high (CAS
has completed pulling low 8 times).
26
0.60 20
0.58 16
0.56 12
100 1k 10k 100k 1M 10M
R OVA ( ) 2928 G03
Figure 16. External Resistor from OVA to Ground
1.56 212
V CC = 6V
V CC = 5.5V
1.38 V CC = 5V 176
V CC = 4.5V
V CC = 4V
1.20 140
1.02 104
0.84 68
0.66 32
100 1k 10k 100k 1M 10M
R OVA ( ) 2928 G04
Figure 17. External Resistor from OVA to V CC
2928f
相关PDF资料 |
PDF描述 |
|---|---|
| H3CCS-2036G | IDC CABLE - HKC20S/AE20G/HKC20S |
| ZXRE1004FRSTOB | IC VREF SHUNT PREC 1.22V TO-92-3 |
| V110B3V3E100B2 | CONVERTER MOD DC/DC 3.3V 100W |
| ELC-06D101E | COIL CHOKE 100UH RADIAL |
| RS3-4805DZ/H3 | CONV DC/DC 3W 20-60VIN +/-05VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1029A | 制造商:Linear Technology 功能描述:EVAL BOARD, LTC2928 QUAD POWER SUPPLY SE |
| DC102F2K | 制造商:U S SENSOR 功能描述:thermistor |
| DC102K | 制造商:RAYTHN 功能描述: |
| DC102R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DC-102R | 制造商:未知厂家 制造商全称:未知厂家 功能描述:1.8watt 24pins DIP/DIL |
发布紧急采购，3分钟左右您将得到回复。