- 您现在的位置：买卖IC网 > PDF目录18713 > DR-TRC103-915-EV (RFM)BOARD EVALUATION 915MHZ RFM RFIC PDF资料下载
参数资料
| 型号： | DR-TRC103-915-EV |
| 厂商： | RFM |
| 文件页数： | 44/65页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION 915MHZ RFM RFIC |
| 标准包装： | 1 |
| 类型： | 收发器，SRR |
| 频率： | 902MHz ~ 928MHz |
| 适用于相关产品： | TRC103-915 |
| 已供物品： | 2 个板，天线，电池 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页
phase noise reciprocal mixing. The two tank circuit inductors have the same value which depends on the band of
operation and the PCB layout. Typical values are given in Table 54 (location of L5 & L6 shown in Figure 2):
Band
863-870 MHz
902-928 MHz
950-960 MHz
L5 & L6
6.8 nH
5.6 nH
5.6 nH
Tolerance
±5%
±5%
±5%
Table 54
The tank circuit inductors should be mounted close to their IC pads with the long axis of the coil at right angles to
the edge of the IC where the pads are located. The decoupling capacitors should be positioned on each side of
the tank circuit inductors. Other RF chokes and coils should be spaced somewhat away from the tank inductors
and positioned at right angles to minimize coupling.
VCO frequency centering is checked by looking at the voltage between pads 6 and 7. The voltage should be 150
±50 mV when the TRC103 is in transmit mode at a frequency near the center of the operating band. VCO fre-
quency centering can be adjusted by changing the value of the tuning inductors and/or adjusting the VCO trim bits
1 and 2 in configuration register MCFG00 . The trim bits adjust the tuning voltage in increments of about 60 mV.
Increasing the value of the tuning inductors increases the tuning voltage between pads 6 and 7.
6.2 Determining Configuration Values for FSK Modulation
6.2.1 Bit Rate Related FSK Configuration Values
The TRC103 supports RF bit rates (data rates) from 1.5625 to 200 kb/s for FSK modulation. There are several
considerations in choosing a bit rate. The sensitivity of the TRC103 decreases with increasing data rate. A bit rate
should be chosen that is adequate but not higher than the application requires. The exceptions to this rule are
when the TRC103 is operated as a frequency hopping or DTS spread spectrum transceiver. In the case of fre-
quency hopping, running at a higher bit rate will allow a higher channel hopping rate, which provides more robust
operation in a crowded band in trade-off for less range under quiet band conditions. DTS signal bandwidth, which
can be achieved using 133 kHz deviation, allows the TRC103 to be operated at full rated output power under FCC
15.247 and similar regulations.
The TRC103 RF bit rate is set by the value of the byte loaded in MCFG03 . For the standard crystal frequency of
12.8 MHz:
BR = 12800/(64*(D + 1)), with D in the range of 0 to 127
Where BR is the bit rate in kb/s and D is the integer stored in MCFG03 . This configuration value supports both the
data and clock recovery circuit in the receiver and the bit rate clocking in the transmitter modulator. Solving the
equation above for D:
D = (12800 - 64*BR)/64*BR
D must be an integer value, so BR is limited to 128 discrete values. If the value of D given in the above equation
is not an integer for your desired bit rate, round the value of D down to the nearest integer. You can then calculate
the nearest available bit rate equal to or greater than your desired bit rate.
Selection of the RF data rate allows a suitable FSK deviation to be determined. This, in turn, allows the configura-
tion value for the anti-aliasing filters in the transmitter and the configuration values for the R-C and Butterworth
low-pass filters in the receiver to be determined.
www.RFM.com E-mail: info@rfm.com
? 2009-2010 by RF Monolithics, Inc.
Technical support +1.800.704.6079
Page 44 of 65
TRC103 - 11/29/12
相关PDF资料 |
PDF描述 |
|---|---|
| DR-TRC103-868-EV | BOARD EVALUATION 868MHZ RFM RFIC |
| TC70N6C32K7680 | OSCILLATOR 32.7680 KHZ 2.5V SMD |
| TC70N3A32K7680 | OSCILLATOR 32.7680 KHZ 2.5V SMD |
| TC70L3C32K7680 | OSCILLATOR 32.7680 KHZ 3.3V SMD |
| EK64905-01 | KIT EVAL FOR 64904 NO CABLES |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DR-TRC103-950-DK | 功能描述:KIT DEV 950MHZ RFIC SRR RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| DR-TRC103-950-EV | 功能描述:BOARD EVALUATION 950MHZ RFM RFIC RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| DR-TRC104-2400-DK | 功能描述:射频开发工具 TRC104 Development Kit 2.4 GHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| DR-TRC104-2400-EV | 制造商:RFM 功能描述:BOARD EVALUATION 2.4GHZ RFM RFIC |
| DR-TRC105-304-DK | 功能描述:射频开发工具 TRC105 Development Kit 303-307 MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。