- 您现在的位置：买卖IC网 > PDF目录18713 > DR-TRC105-304-EV (RFM)BOARD EVALUATION 304MHZ RFM RFIC PDF资料下载
参数资料
| 型号： | DR-TRC105-304-EV |
| 厂商： | RFM |
| 文件页数： | 17/67页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION 304MHZ RFM RFIC |
| 标准包装： | 1 |
| 类型： | 收发器 |
| 频率： | 303.325MHz ~ 307.3MHz |
| 适用于相关产品： | TRC105 |
| 已供物品： | 2 个板，天线，电池 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
nFIFOEMPY[0] is reset. When the last bit of the 64 byte has been written into the FIFO, signal IRQCFG0D_
th
FIFOFULL[1] is set. Data must be read before the next byte is received or it will be overwritten.
The IRQCFG0D_nFIFOEMPY[0] signal can be used as an interrupt signal for the host microcontroller by map-
ping to pin IRQ0 if IRQCFG0D_RX_IRQ0[7..6] is set to 10. Alternatively, the WRITE_byte signal may also be
used as an interrupt if IRQCFG0D_RX_IRQ0[7..6] is set to 01.
Demodulation in buffered mode occurs in the same way as in continuous mode. Received data is directly read
from the FIFO and the DATA and DCLK pins are not used. Data and clock recovery in buffered mode is automati-
cally enabled. DCLK is not externally available.
The pattern recognition block is automatically enabled in Buffered data mode. The Start Pattern Detect
(PATTERN) signal can be mapped to pin IRQ0. In Buffered data mode RSSI operates the same way as in Con-
tinuous data mode. However, RSSI_IRQ may be mapped to IRQ1 instead of to IRQ0 in Continuous data mode.
Figure 12
3.6 Transmitting in Continuous or Buffered Data Modes
The transmitter operates in Continuous data mode when the MCFG01_Mode [7..6] bits are set to 00. Bit clock
DCLK is available on pin IRQ1. Bits are clocked into the transmitter on the rising edge of this clock. Data must be
stable 2 μs before the rising edge of DCLK and must be held for 2 μs following the rising edge of this clock
(T SUDATA ). To meet this requirement, data can be changed on the falling edge of DCLK. In FSK mode DCLK must
be used but is optional in OOK mode.
The transmitter operates in Buffered data mode when the MCFG01_Mode [5] bit is set to 1. Data to be transmit-
ted is written to the 64-byte FIFO through the SPI interface. FIFO data is loaded byte-by-byte into a shift register
which then transfers the data bit-by-bit to the modulator. FIFO operation in transmit mode is similar to receive
mode. Transmission can start immediately after the first byte of data is written into the FIFO or when the FIFO is
full, as determined by the IRQCFG0E_Start_Full[4] bit setting. If the transmit FIFO is full, the interrupt signal
IRQCFG0D_ FIFOFULL[2] is asserted on pin IRQ1. If data is written into the FIFO while it is full, the flag
IRQCFG0D_FIFO_OVR[0] will be set to 1 and the previous FIFO contents will be overwritten. The IRQCFG0D_
FIFO_OVR[0] flag is cleared by writing a 1 to it. At the same time the contents of the FIFO are cleared. Once the
last data byte in the FIFO is loaded into the shift register driving the transmitter modulator, the flag IRQCFG0D_
nFIFOEMPY[1] is set to 0 on pin IRQ0. If new data is not written to the FIFO and the last bit has been transferred
to the modulator, the IRQCFG0E_TX_STOP[5] bit goes high as the modulator starts to send the last bit. The
transmitter must remain on one bit period after TX_STOP to transmit the last bit. If the transmitter is switched off
(switched to another mode), the transmission stops immediately even if there is still data in the shift register. In
www.RFM.com E-mail: info@rfm.com
? 2009-2013 by RF Monolithics, Inc.
Technical support +1.800.704.6079
Page 17 of 67
TRC105 - 05/29/13
相关PDF资料 |
PDF描述 |
|---|---|
| GSCA06S2 | SWITCH ROTARY SIDE |
| DR-TRC103-950-EV | BOARD EVALUATION 950MHZ RFM RFIC |
| DR-TRC103-915-EV | BOARD EVALUATION 915MHZ RFM RFIC |
| DR-TRC103-868-EV | BOARD EVALUATION 868MHZ RFM RFIC |
| TC70N6C32K7680 | OSCILLATOR 32.7680 KHZ 2.5V SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DR-TRC105-315-DK | 功能描述:射频开发工具 TRC105 Development Kit 310-319 MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| DR-TRC105-315-EV | 功能描述:射频开发工具 TRC105 Evaluation Board 310-319 MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| DR-TRC105-345-DK | 功能描述:射频开发工具 TRC105 Development Kit 342-348 MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| DR-TRC105-345-EV | 功能描述:射频开发工具 TRC105 Evaluation Board 342-348 MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| DR-TRC105-372-DK | 功能描述:射频开发工具 TRC105 Development Kit 365-381 MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。