- 您现在的位置：买卖IC网 > PDF目录295503 > DS1075M-60 (MAXIM INTEGRATED PRODUCTS INC) 60 MHz, OTHER CLOCK GENERATOR, PDIP8 PDF资料下载
参数资料
| 型号： | DS1075M-60 |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | XO, clock |
| 英文描述： | 60 MHz, OTHER CLOCK GENERATOR, PDIP8 |
| 封装： | 0.300 INCH, DIP-8 |
| 文件页数： | 2/18页 |
| 文件大小： | 251K |
| 代理商： | DS1075M-60 |
DS1075
10 of 18
Figure 9
POWER-ON RESET
When power is initially applied to the device supply pin, a power-on reset sequence is executed, similar
to that which occurs when the device is restored from a power-down condition. This sequence comprises
two stages, first a conventional POR to initialize all on-chip circuitry, followed by a stabilization period
to allow the oscillator to reach a stable frequency before enabling the outputs:
1. Initialize internal circuitry.
2. Enable internal oscillator and/or OSCIN buffer.
3. Set M and N to maximum values.
4. Wait approximately 256 cycles of MCLK for the oscillator to stabilize.
5. Load M and N programmed values from EEPROM.
6. Enable OUT0 (assuming EN0=0).
7. Enable OUT.
Figure 10
PROGRAMMING
Normally when power is applied to the supply voltage pin the device will enter its normal operating mode
following the power-on reset sequence. However the device can be made to enter a programming mode if
a pull-up resistor is connected between IN/OUT and the supply voltage pin, prior to power-up. The
method used for programming is a variant of the 1-Wire protocol used on a number of Dallas
Semiconductor products.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1233Z-10N | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4 |
| DS1283SN | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| DS1543W-120 | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
| DS1644L-15 | 0 TIMER(S), REAL TIME CLOCK, DSO34 |
| DS1706RESA+T&R | 3.3 and 5.0 Volt MicroMonitor |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1075M-60IND | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Oscillator/Divider |
| DS1075M-60N | 功能描述:可编程振荡器 RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1075M-66 | 功能描述:可编程振荡器 RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1075M-66IND | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Oscillator/Divider |
| DS1075M-66N | 功能描述:可编程振荡器 RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
发布紧急采购，3分钟左右您将得到回复。