- 您现在的位置：买卖IC网 > PDF目录97857 > DS1077Z-100 (DALLAS SEMICONDUCTOR) 100 MHz, OTHER CLOCK GENERATOR, PDSO8 PDF资料下载
参数资料
| 型号： | DS1077Z-100 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Clock Generator |
| 英文描述： | 100 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| 封装： | 0.150 INCH, SOIC-8 |
| 文件页数： | 15/17页 |
| 文件大小： | 103K |
| 代理商： | DS1077Z-100 |
DS1077
7 of 17
(Refer to Table 5)
Table 5
Bit Value
Divisor (N)
0 000 000 000
**
2
0 000 000 001
3
--
1 111 111 111
1025
**Default Condition
BUS WORD
Name
---
B
WC
A2
A1
A0
Factory Default
0*0*0*0*
0
*These bits are reserved and must be set to “0” zero
A0,A1,A2
(Default Setting = 000)
These are the device select bits which determine the address of the device.
WC
(Default Setting WC=0)
This bit determines when/if the EEPROM is written to after register contents have been changed.
If WC = 0 the EEPROM is written automatically after a write register command.
If WC = 1 the EEPROM is only written when the “WRITE ” command is issued.
Regardless of the value of the WC bit the value of the BUS Register (A0,A1,A2) is always written
immediately to the EEPROM.
2-WIRE SERIAL DATA BUS
The DS1077 supports a bi-directional two-wire bus and data transmission protocol. A device that sends
data onto the bus is defined as a transmitter, and a device receiving data as a receiver. The device that
controls the message is called a "master". The devices that are controlled by the master are "slaves". The
bus must be controlled by a master device which generates the serial clock (SCL), controls the bus access,
and generates the START and STOP conditions. The DS1077 operates as a slave on the two-wire bus.
Connections to the bus are made via the open-drain I/O lines SDA* and SCL. A pullup resistor (5K) is
connected to SDA
The following bus protocol has been defined (See Figure 2):
Data transfer may be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes
in the data line while the clock line is high will be interpreted as control signals.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1100U-175/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
| DS1100U-40/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
| DS1100U-45/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
| DS1100Z-150/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
| DS1100Z-175/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1077Z-100+ | 功能描述:可编程振荡器 EconOscillator/Dvdr 100MHz 118mil 2-Wire RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1077Z-100+T&R | 制造商:Maxim Integrated Products 功能描述:ECO OSC 100MHZ 2-WIRE 8P-SO TRL LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC ECONOSCILLATOR 100MHZ 8-SOIC |
| DS1077Z-100+T&R | 功能描述:可编程振荡器 EconOscillator/Dvdr 100MHz 118mil 2-Wire RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1077Z-120 | 功能描述:可编程振荡器 EconOscillator/Dvdr 120MHz 118mil 2-Wire RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
| DS1077Z-120+ | 功能描述:可编程振荡器 EconOscillator/Dvdr 120MHz 118mil 2-Wire RoHS:否 制造商:IDT 封装 / 箱体:5 mm x 7 mm x 1.5 mm 频率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 频率稳定性:+/- 50 PPM 电源电压:3.63 V 负载电容:10 pF 端接类型:SMD/SMT 输出格式:LVPECL 最小工作温度:- 40 C 最大工作温度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封装: |
发布紧急采购，3分钟左右您将得到回复。