- 您现在的位置：买卖IC网 > Datasheet目录409 > DS1820 (Maxim Integrated)IC DGTL THERMOMETER TO92-3 Datasheet资料下载
参数资料
| 型号： | DS1820 |
| 厂商： | Maxim Integrated |
| 文件页数： | 14/23页 |
| 文件大小： | 0K |
| 描述： | IC DGTL THERMOMETER TO92-3 |
| 其它有关文件： | DS1820 Digital Thermometer |
| 标准包装： | 500 |
| 感应温度： | -55°C ~ 125°C |
| 输出类型： | 开路漏极 |
| 电源电压： | 3 V ~ 5.5 V |
| 精确度： | ±0.5°C |
| 封装/外壳： | TO-226-3、TO-92-3 标准主体 |
| 供应商设备封装： | TO-92 |
| 包装： | 散装 |
DS18S20
READ-TIME SLOTS
The DS18S20 can only transmit data to the master when the master issues read-time slots. Therefore, the
master must generate read-time slots immediately after issuing a Read Scratchpad [BEh] or Read Power
Supply [B4h] command, so that the DS18S20 can provide the requested data. In addition, the master can
generate read-time slots after issuing Convert T [44h] or Recall E 2 [B8h] commands to find out the status
of the operation as explained in the DS18S20 Function Commands section.
All read-time slots must be a minimum of 60 μ s in duration with a minimum of a 1 μ s recovery time
between slots. A read-time slot is initiated by the master device pulling the 1-Wire bus low for a
minimum of 1 μ s and then releasing the bus (see Figure 11). After the master initiates the read-time slot,
the DS18S20 will begin transmitting a 1 or 0 on bus. The DS18S20 transmits a 1 by leaving the bus high
and transmits a 0 by pulling the bus low. When transmitting a 0, the DS18S20 will release the bus by the
end of the time slot, and the bus will be pulled back to its high idle state by the pullup resister. Output
data from the DS18S20 is valid for 15 μ s after the falling edge that initiated the read-time slot. Therefore,
the master must release the bus and then sample the bus state within 15 μ s from the start of the slot.
Figure 12 illustrates that the sum of T INIT , T RC , and T SAMPLE must be less than 15 μ s for a read-time slot.
Figure 13 shows that system timing margin is maximized by keeping T INIT and T RC as short as possible
and by locating the master sample time during read-time slots towards the end of the 15 μ s period.
Figure 11. Read/Write Time Slot Timing Diagram
START
OF SLOT
START
OF SLOT
V PU
1-WIRE BUS
GND
MASTER WRITE “0” SLOT
60 μ s < T X “0” < 120 μ s
MASTER WRITE “1” SLOT
1 μ s < T REC < ∞
> 1 μ s
MIN
DS18S20 Samples
TYP
MAX
MIN
DS18S20 Samples
TYP
MAX
15 μ s
15 μ s
30 μ s
15 μ s
15 μ s
30 μ s
V PU
1-WIRE BUS
GND
MASTER READ “0” SLOT
MASTER READ “1” SLOT
1 μ s < T REC < ∞
> 1 μ s
15 μ s
Master samples
45 μ s
> 1 μ s
15 μ s
Master samples
LINE TYPE LEGEND
Bus master pulling low
Resistor pullup
14 of 23
DS18S20 pulling low
相关PDF资料 |
PDF描述 |
|---|---|
| DS1822+PAR | IC THERMOMETER ECONO DIG TO-92 |
| DS1822Z/T&R | IC THERMOMETER ECONO DIG 8-SOIC |
| DS1870E-010+T&R | IC CNTRLR RF POWER AMP 16TSSOP |
| DS18S20-PAR+T&R | IC THERM MICROLAN HI-PREC TO-92 |
| DS60R+T&R | IC SENSOR MICRO CENTIGRADE SOT23 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1820K | 制造商:Maxim Integrated Products 功能描述:THERMOMETER DEMO KIT |
| DS1820S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DS1820.DS1820S Digital Thermometer Replacements |
| DS1821 | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1821_07 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Programmable Digital Thermostat and Thermometer |
| DS1821+ | 功能描述:板上安装温度传感器 Programmable Digital Thermostat/Thrmmtr RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。