参数资料
型号: DS1820
厂商: Maxim Integrated
文件页数: 7/23页
文件大小: 0K
描述: IC DGTL THERMOMETER TO92-3
其它有关文件: DS1820 Digital Thermometer
标准包装: 500
感应温度: -55°C ~ 125°C
输出类型: 开路漏极
电源电压: 3 V ~ 5.5 V
精确度: ±0.5°C
封装/外壳: TO-226-3、TO-92-3 标准主体
供应商设备封装: TO-92
包装: 散装
the scratchpad at any time using the Recall E [B8h] command. The master can issue “read-time slots”
DS18S20
MEMORY
The DS18S20’s memory is organized as shown in Figure 7. The memory consists of an SRAM
scratchpad with nonvolatile EEPROM storage for the high and low alarm trigger registers (T H and T L ).
Note that if the DS18S20 alarm function is not used, the T H and T L registers can serve as general-purpose
memory. All memory commands are described in detail in the DS18S20 Function Commands section.
Byte 0 and byte 1 of the scratchpad contain the LSB and the MSB of the temperature register,
respectively. These bytes are read-only. Bytes 2 and 3 provide access to T H and T L registers. Bytes 4 and
5 are reserved for internal use by the device and cannot be overwritten; these bytes will return all 1s when
read. Bytes 6 and 7 contain the COUNT REMAIN and COUNT PER oC registers, which can be used to
calculate extended resolution results as explained in the Operation—Measuring Temperature section.
Byte 8 of the scratchpad is read-only and contains the CRC code for bytes 0 through 7 of the scratchpad.
The DS18S20 generates this CRC using the method described in the CRC Generation section.
Data is written to bytes 2 and 3 of the scratchpad using the Write Scratchpad [4Eh] command; the data
must be transmitted to the DS18S20 starting with the least significant bit of byte 2. To verify data
integrity, the scratchpad can be read (using the Read Scratchpad [BEh] command) after the data is
written. When reading the scratchpad, data is transferred over the 1-Wire bus starting with the least
significant bit of byte 0. To transfer the T H and T L data from the scratchpad to EEPROM, the master must
issue the Copy Scratchpad [48h] command.
Data in the EEPROM registers is retained when the device is powered down; at power-up the EEPROM
data is reloaded into the corresponding scratchpad locations. Data can also be reloaded from EEPROM to
2
(see the 1-Wire Bus System section) following the Recall E 2 command and the DS18S20 will indicate the
status of the recall by transmitting 0 while the recall is in progress and 1 when the recall is done.
Figure 7. DS18S20 Memory Map
SCRATCHPAD
(POWER-UP STATE)
Byte 0 Temperature LSB (AAh)
Byte 1 Temperature MSB (00h)
Byte 2 T H Register or User Byte 1*
Byte 3 T L Register or User Byte 2*
(85°C)
EEPROM
T H Register or User Byte 1
T L Register or User Byte 2
Byte 4 Reserved (FFh)
Byte 5 Reserved (FFh)
Byte 6 COUNT REMAIN (0Ch)
Byte 7 COUNT PER °C (10h)
Byte 8 CRC*
* Power-up state depends on value(s) stored in EEPROM.
7 of 23
相关PDF资料
PDF描述
DS1822+PAR IC THERMOMETER ECONO DIG TO-92
DS1822Z/T&R IC THERMOMETER ECONO DIG 8-SOIC
DS1870E-010+T&R IC CNTRLR RF POWER AMP 16TSSOP
DS18S20-PAR+T&R IC THERM MICROLAN HI-PREC TO-92
DS60R+T&R IC SENSOR MICRO CENTIGRADE SOT23
相关代理商/技术参数
参数描述
DS1820K 制造商:Maxim Integrated Products 功能描述:THERMOMETER DEMO KIT
DS1820S 制造商:未知厂家 制造商全称:未知厂家 功能描述:DS1820.DS1820S Digital Thermometer Replacements
DS1821 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1821_07 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Programmable Digital Thermostat and Thermometer
DS1821+ 功能描述:板上安装温度传感器 Programmable Digital Thermostat/Thrmmtr RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor