- 您现在的位置：买卖IC网 > Datasheet目录409 > DS1820 (Maxim Integrated)IC DGTL THERMOMETER TO92-3 Datasheet资料下载
参数资料
| 型号： | DS1820 |
| 厂商： | Maxim Integrated |
| 文件页数： | 3/23页 |
| 文件大小： | 0K |
| 描述： | IC DGTL THERMOMETER TO92-3 |
| 其它有关文件： | DS1820 Digital Thermometer |
| 标准包装： | 500 |
| 感应温度： | -55°C ~ 125°C |
| 输出类型： | 开路漏极 |
| 电源电压： | 3 V ~ 5.5 V |
| 精确度： | ±0.5°C |
| 封装/外壳： | TO-226-3、TO-92-3 标准主体 |
| 供应商设备封装： | TO-92 |
| 包装： | 散装 |
DS18S20
Figure 1. DS18S20 Block Diagram
V PU
4.7k
PARASITE POWER
CIRCUIT
MEMORY CONTROL
LOGIC
DS18S20
DQ
TEMPERATURE SENSOR
GND
C PP
INTERNAL V DD
64-BIT ROM
AND
1-Wire PORT
SCRATCHPAD
ALARM HIGH TRIGGER (T H )
REGISTER (EEPROM)
V DD
POWER-
SUPPLY
SENSE
ALARM LOW TRIGGER (T L )
REGISTER (EEPROM)
8-BIT CRC GENERATOR
OPERATION—MEASURING TEMPERATURE
The core functionality of the DS18S20 is its direct-to-digital temperature sensor. The temperature sensor
output has 9-bit resolution, which corresponds to 0.5 ° C steps. The DS18S20 powers-up in a low-power
idle state; to initiate a temperature measurement and A-to-D conversion, the master must issue a Convert
T [44h] command. Following the conversion, the resulting thermal data is stored in the 2-byte
temperature register in the scratchpad memory and the DS18S20 returns to its idle state. If the DS18S20
is powered by an external supply, the master can issue “read-time slots” (see the 1-Wire Bus System
section) after the Convert T command and the DS18S20 will respond by transmitting 0 while the
temperature conversion is in progress and 1 when the conversion is done. If the DS18S20 is powered with
parasite power, this notification technique cannot be used since the bus must be pulled high by a strong
pullup during the entire temperature conversion. The bus requirements for parasite power are explained in
detail in the Powering the DS18S20 section.
The DS18S20 output data is calibrated in degrees centigrade; for Fahrenheit applications, a lookup table
or conversion routine must be used. The temperature data is stored as a 16-bit sign-extended two’s
complement number in the temperature register (see Figure 2). The sign bits (S) indicate if the
temperature is positive or negative: for positive numbers S = 0 and for negative numbers S = 1. Table 1
gives examples of digital output data and the corresponding temperature reading.
Resolutions greater than 9 bits can be calculated using the data from the temperature, COUNT REMAIN
and COUNT PER °C registers in the scratchpad. Note that the COUNT PER °C register is hard-wired to
16 (10h). After reading the scratchpad, the TEMP_READ value is obtained by truncating the 0.5 ° C bit
(bit 0) from the temperature data (see Figure 2). The extended resolution temperature can then be
calculated using the following equation:
TEMPERATUR E = TEMP _ READ ? 0 . 25 +
COUNT _ PER _ C ? COUNT _ REMAIN
COUNT _ PER _ C
3 of 23
相关PDF资料 |
PDF描述 |
|---|---|
| DS1822+PAR | IC THERMOMETER ECONO DIG TO-92 |
| DS1822Z/T&R | IC THERMOMETER ECONO DIG 8-SOIC |
| DS1870E-010+T&R | IC CNTRLR RF POWER AMP 16TSSOP |
| DS18S20-PAR+T&R | IC THERM MICROLAN HI-PREC TO-92 |
| DS60R+T&R | IC SENSOR MICRO CENTIGRADE SOT23 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1820K | 制造商:Maxim Integrated Products 功能描述:THERMOMETER DEMO KIT |
| DS1820S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DS1820.DS1820S Digital Thermometer Replacements |
| DS1821 | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1821_07 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Programmable Digital Thermostat and Thermometer |
| DS1821+ | 功能描述:板上安装温度传感器 Programmable Digital Thermostat/Thrmmtr RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。