- 您现在的位置：买卖IC网 > Datasheet目录409 > DS1820 (Maxim Integrated)IC DGTL THERMOMETER TO92-3 Datasheet资料下载
参数资料
| 型号： | DS1820 |
| 厂商： | Maxim Integrated |
| 文件页数： | 5/23页 |
| 文件大小： | 0K |
| 描述： | IC DGTL THERMOMETER TO92-3 |
| 其它有关文件： | DS1820 Digital Thermometer |
| 标准包装： | 500 |
| 感应温度： | -55°C ~ 125°C |
| 输出类型： | 开路漏极 |
| 电源电压： | 3 V ~ 5.5 V |
| 精确度： | ±0.5°C |
| 封装/外壳： | TO-226-3、TO-92-3 标准主体 |
| 供应商设备封装： | TO-92 |
| 包装： | 散装 |
DS18S20
POWERING THE DS18S20
The DS18S20 can be powered by an external supply on the V DD pin, or it can operate in “parasite power”
mode, which allows the DS18S20 to function without a local external supply. Parasite power is very
useful for applications that require remote temperature sensing or those with space constraints.
Figure 1 shows the DS18S20’s parasite-power control circuitry, which “steals” power from the 1-Wire
bus via the DQ pin when the bus is high. The stolen charge powers the DS18S20 while the bus is high,
and some of the charge is stored on the parasite power capacitor (C PP ) to provide power when the bus is
low. When the DS18S20 is used in parasite power mode, the V DD pin must be connected to ground.
In parasite power mode, the 1-Wire bus and C PP can provide sufficient current to the DS18S20 for most
operations as long as the specified timing and voltage requirements are met (see the DC Electrical
Characteristics and the AC Electrical Characteristics ). However, when the DS18S20 is performing
temperature conversions or copying data from the scratchpad memory to EEPROM, the operating current
can be as high as 1.5mA. This current can cause an unacceptable voltage drop across the weak 1-Wire
pullup resistor and is more current than can be supplied by C PP . To assure that the DS18S20 has sufficient
supply current, it is necessary to provide a strong pullup on the 1-Wire bus whenever temperature
conversions are taking place or data is being copied from the scratchpad to EEPROM. This can be
accomplished by using a MOSFET to pull the bus directly to the rail as shown in Figure 4. The 1-Wire
bus must be switched to the strong pullup within 10 μ s (max) after a Convert T [44h] or Copy Scratchpad
[48h] command is issued, and the bus must be held high by the pullup for the duration of the conversion
(t CONV ) or data transfer (t WR = 10ms). No other activity can take place on the 1-Wire bus while the pullup
is enabled.
The DS18S20 can also be powered by the conventional method of connecting an external power supply to
the V DD pin, as shown in Figure 5. The advantage of this method is that the MOSFET pullup is not
required, and the 1-Wire bus is free to carry other traffic during the temperature conversion time.
The use of parasite power is not recommended for temperatures above 100 ° C since the DS18S20 may not
be able to sustain communications due to the higher leakage currents that can exist at these temperatures.
For applications in which such temperatures are likely, it is strongly recommended that the DS18S20 be
powered by an external power supply.
In some situations the bus master may not know whether the DS18S20s on the bus are parasite powered
or powered by external supplies. The master needs this information to determine if the strong bus pullup
should be used during temperature conversions. To get this information, the master can issue a Skip ROM
[CCh] command followed by a Read Power Supply [B4h] command followed by a “read-time slot”.
During the read-time slot, parasite powered DS18S20s will pull the bus low, and externally powered
DS18S20s will let the bus remain high. If the bus is pulled low, the master knows that it must supply the
strong pullup on the 1-Wire bus during temperature conversions.
5 of 23
相关PDF资料 |
PDF描述 |
|---|---|
| DS1822+PAR | IC THERMOMETER ECONO DIG TO-92 |
| DS1822Z/T&R | IC THERMOMETER ECONO DIG 8-SOIC |
| DS1870E-010+T&R | IC CNTRLR RF POWER AMP 16TSSOP |
| DS18S20-PAR+T&R | IC THERM MICROLAN HI-PREC TO-92 |
| DS60R+T&R | IC SENSOR MICRO CENTIGRADE SOT23 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1820K | 制造商:Maxim Integrated Products 功能描述:THERMOMETER DEMO KIT |
| DS1820S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DS1820.DS1820S Digital Thermometer Replacements |
| DS1821 | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS1821_07 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Programmable Digital Thermostat and Thermometer |
| DS1821+ | 功能描述:板上安装温度传感器 Programmable Digital Thermostat/Thrmmtr RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。