- 您现在的位置：买卖IC网 > PDF目录171225 > DS1862AB+ (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY CONSUMER CIRCUIT, PBGA25 PDF资料下载
参数资料
| 型号： | DS1862AB+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA25 |
| 封装： | 5 X 5 MM, ROHS COMPLIANT, CSBGA-25 |
| 文件页数： | 13/42页 |
| 文件大小： | 586K |
| 代理商： | DS1862AB+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
DS1862A
XFP Laser Control and Digital Diagnostic IC
20
______________________________________________________________________________________
/* Assume that the Null input is 0.5V. */
/* In addition, the requirement for LSB is 50μV. */
FS = 65536 * 50e-6;
/* 3.2768 */
CNT1 = 0.5 / 50e-6;
/* 10000 */
CNT2 = 0.90*FS / 50e-6;
/* 58982 */
/* Thus the NULL input of 0.5V and the 90% of FS input
is 2.94912V. */
set the trim-offset-register to zero;
set Right-Shift register to zero (Typically zero.
See the Right-Shifting section);
gain_result = 0h;
CLAMP = FFF8h/2^(Right_Shift_Register);
For n = 15 down to 0
begin
gain_result = gain_result + 2^n;
Force the 90% FS input (2.94912V);
Meas2 = read the digital result from the part;
If Meas2 >= CLAMP then
gain_result = gain_result - 2^n;
Else
Force the NULL input (0.5V);
Meas1 = read the digital result from the part;
if (Meas2 - Meas1) > (CNT2 - CNT1) then
gain_result = gain_result - 2^n;
end;
Set the gain register to gain_result;
The gain register is now set and the resolution of the
conversion will best match the expected LSB. The next
step is to calibrate the offset of the DS1862A. With the
correct gain value written to the gain register, again
force the NULL input to the monitor pin. Read the digi-
tal result from the part (Meas1). The offset value is
equal to negative value of Meas1.
The calculated offset is now written to the DS1862A
and the gain and offset-scaling procedure is complete.
Right-Shifting A/D Conversion Result
(Scalable Dynamic Ranging)
Right-shifting is a digital method used to regain some
of the lost ADC range of a calibrated system. If right-
shifting is enabled, by simply loading a non-zero value
into the appropriate Right-Shifting Register, then the
DS1862A shifts the calibrated result just before it is
stored into the monitor channels’ register. If a system is
calibrated so the maximum expected input results in a
digital output value of less than 7FFFh (50% of FS),
then it is a candidate for using the right-shifting
method.
If the maximum desired digital output is less than
7FFFh, then the calibrated system is using less than 1/2
the ADC’s range. Similarly, if the maximum desired dig-
ital output is less than 1FFFh, then the calibrated sys-
tem is only using 1/8th the ADC’s range. For example, if
an applied maximum analog signal yields a maximum
digital output less than 1FFCh, then only 1/8th of the
ADC’s range is used. Right-shifting improves the reso-
lution of the measured signal as part of internal calibra-
tion. Without right-shifting, the 3 MS bits of the ADC will
never be used. In this example, a value of 3 for the
right-shifting maximizes the ADC range and a larger
gain setting must be loaded to achieve optimal conver-
sion. No resolution is lost since this is a 13-bit converter
that is left justified. The value can be right-shifted 3
times without losing any resolution. The following table
describes when the right-shifting method can be effec-
tively used.
OFFSET REGISTER
Meas
_
()
=
11
4
Table 10. Right-Shifting Selection
OUTPUT RANGE USED WITH
ZERO RIGHT-SHIFTS
NUMBER OF RIGHT-
SHIFTS NEEDED
0h .. FFFFh
0
0h .. 7FFFh
1
0h .. 3FFFh
2
0h .. 1FFFh
3
0h .. 0FFFh
4
相关PDF资料 |
PDF描述 |
|---|---|
| DS1862AB+T&R | SPECIALTY CONSUMER CIRCUIT, PBGA25 |
| DS1868-100-IND | 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDIP14 |
| DS2-320-2AR | DIP20, IC SOCKET |
| DS1-314-1AR | DIP14, IC SOCKET |
| DS3-328-1AR | DIP28, IC SOCKET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1862AB+ | 功能描述:激光驱动器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862AB+T&R | 制造商:Maxim Integrated Products 功能描述:XFP LASER CONTROL 25CSBGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1862AB+T&R | 功能描述:激光驱动器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862AB+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC |
| DS1862B | 功能描述:激光驱动器 RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。