- 您现在的位置：买卖IC网 > PDF目录171225 > DS1862AB+ (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY CONSUMER CIRCUIT, PBGA25 PDF资料下载
参数资料
| 型号： | DS1862AB+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA25 |
| 封装： | 5 X 5 MM, ROHS COMPLIANT, CSBGA-25 |
| 文件页数： | 40/42页 |
| 文件大小： | 586K |
| 代理商： | DS1862AB+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页
DS1862A
XFP Laser Control and Digital Diagnostic IC
_______________________________________________________________________________________
7
FAST ALARMS AND VCC FAULT CHARACTERISTICS
(VCC3 = +2.9V to +5.5V, VCC2 = +1.6V to +3.6V, TA = -40°C to +100°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
HIGH BIAS and TX-P Threshold
FS
(Note 10)
2.48
2.5
2.52
mA
VCC2/3 Fault Asserted
Falling Edge Delay
VCC2/3
(Note 11)
75
ms
QT Temperature Coefficient
-3
+3
%
QT Voltage Coefficient
0.5
%/V
QT FS Trim Accuracy (4.2V,
+25°C)
2.480
2.500
2.520
mA
QT Accuracy (Trip) (INL)
-2
0
+2
LSB
QT Voltco
0.5
%/V
QT Tempco
1.5
3
%
Note 1:
All voltages are referenced to ground. Current into the IC is positive, and current out of the IC is negative.
Note 2:
Secondary power supply is used to support optional variable power-supply feature of the XFP module. If VCC2 is not used
(i.e., signal conditioners using 3.3V supply), VCC2 should be connected to the VCC3.
Note 3:
Input signals (i.e., TX-D, MOD-DESEL, and P-DOWN/RST) have internal pullup resistors.
Note 4:
Guaranteed by design. Simulated over process and 50μA < IBMD < 1500μA.
Note 5:
CB—total capacitance of one bus line in picofarads.
Note 6:
EEPROM write begins after a STOP condition occurs.
Note 7:
This is the maximum and minimum voltage on the MODSET and BIASSET pins required to meet accuracy and drift specifi-
cations.
Note 8:
For VTHRSET, offset may be as much as 10mV.
Note 9:
This is the uncalibrated offset provided by the factory; offset adjustment is available on this channel.
Note 10: %FS refers to calibrated FS in case of internal calibration, and uncalibrated FS in the case of external calibration.
Uncalibrated FS is set in the factory and specified in this data sheet as FS (factory). Calibrated FS is set by the user, allow-
ing a change in any monitored channel scale.
Note 11: See the
Monitor Channels section for more detail or VCC2 and VCC3 selection.
NONVOLATILE MEMORY CHARACTERISTICS
(VCC3 = +2.9V to +5.5V, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Endurance (Write Cycle)
+70°C
50k
Cycles
Endurance (Write Cycle)
+25°C
200k
Cycles
相关PDF资料 |
PDF描述 |
|---|---|
| DS1862AB+T&R | SPECIALTY CONSUMER CIRCUIT, PBGA25 |
| DS1868-100-IND | 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDIP14 |
| DS2-320-2AR | DIP20, IC SOCKET |
| DS1-314-1AR | DIP14, IC SOCKET |
| DS3-328-1AR | DIP28, IC SOCKET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1862AB+ | 功能描述:激光驱动器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862AB+T&R | 制造商:Maxim Integrated Products 功能描述:XFP LASER CONTROL 25CSBGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1862AB+T&R | 功能描述:激光驱动器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862AB+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC |
| DS1862B | 功能描述:激光驱动器 RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。