- 您现在的位置：买卖IC网 > PDF目录171225 > DS1862AB+ (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY CONSUMER CIRCUIT, PBGA25 PDF资料下载
参数资料
| 型号： | DS1862AB+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA25 |
| 封装： | 5 X 5 MM, ROHS COMPLIANT, CSBGA-25 |
| 文件页数： | 16/42页 |
| 文件大小： | 586K |
| 代理商： | DS1862AB+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
DS1862A
XFP Laser Control and Digital Diagnostic IC
______________________________________________________________________________________
23
can only be reset by pulsing the P-DOWN/RST pin high
for the reset time, tRESET, or by toggling the SOFT P-
DOWN/RST bit in Byte 6Eh, bit 3. See the
Power-
Down/Reset Pin section for more details.
Power-Down/Reset Pin
The P-DOWN/RST pin is a multifunction input pin that
resets and/or powers down the DS1862A. Since the pin
is internally pulled up, its normal state is released, which
corresponds to power-down mode. If the P-DOWN/RST
pin is released, or driven high, the DS1862A responds
by shutting down the MODSET and BIASSET currents.
Once the pin is pulled low, operation continues (if not
inhibited by a safety fault). Besides powering down the
DS1862A, a high-going pulse with minimum reset time,
tRESET, can be applied to the P-DOWN/RST pin. This is
necessary to restart the DS1862A, especially if it is in a
safety shutdown condition and needs to be restarted
after the safety condition has been rectified. See the tim-
ing diagrams for proper pin timing.
Power-Down Functionality
During power-down mode IBIASSET and IMODSET drop
below 10μA, effectively shutting down the laser. FETG
is not asserted and safety faults do not occur during
this period. During power-down, I2C communication is
still active, but the signal conditioner pins EN1 and EN2
are noncontrollable and automatically change to the
states: EN1 = 1 and EN2 = 0. Other internal flags/sig-
nals that are based on the signal conditioner inputs still
reflect the status on the signal conditioner pins during
power-down. For example, RX-LOS still reflects the sta-
tus of SC-RX-LOS, and MOD-NR still reflects the logical
states for the signal conditioner pins. Similarly, it is pos-
sible for FETG to be asserted, even though the BIAS-
SET and MODSET currents are shut down. However,
during power-down and a short period, tPDR-OFF, dur-
ing power-up, TX-P Low flag is ignored (internally auto-
matically masked out) and does not contribute to
FETG’s logic.
SHUTDOWN LOGIC
BMD (PIN)
(TX-P CURRENT)
BMD (PIN)
(TX-P CURRENT)
LOW TX-P MASK
HIGH TX-P MASK
QT LOW
TX-P FLAG
QT HIGH
TX-P FLAG
ADC
THRESHOLD
ADC
THRESHOLD
HIGH BIAS MASK
QT HIGH
BIAS FLAG
BIASSET (PIN)
(BIASSET CURRENT)
ADC
THRESHOLD
SOFT TX-D
P-DOWN/RST (PIN)
TX-D (PIN)
SHUTDOWN
FLAG
SAFETY FLAG
SOFT P-DOWN/RST
QT LOW TX-P FLAG
QT HIGH TX-P FLAG
SAFETY FLAG
FETG_POL
DRIVE A P-CHANNEL SWITCH
DRIVE A N-CHANNEL SWITCH
0
1
QT HIGH BIAS FLAG
LA
TCH
LATCHED-TX-FAULT
LA
TCH
FETG (PIN)
FETG_POL
Figure 12. Safety Fault and Shutdown Logic
相关PDF资料 |
PDF描述 |
|---|---|
| DS1862AB+T&R | SPECIALTY CONSUMER CIRCUIT, PBGA25 |
| DS1868-100-IND | 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDIP14 |
| DS2-320-2AR | DIP20, IC SOCKET |
| DS1-314-1AR | DIP14, IC SOCKET |
| DS3-328-1AR | DIP28, IC SOCKET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1862AB+ | 功能描述:激光驱动器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862AB+T&R | 制造商:Maxim Integrated Products 功能描述:XFP LASER CONTROL 25CSBGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1862AB+T&R | 功能描述:激光驱动器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862AB+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC |
| DS1862B | 功能描述:激光驱动器 RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。