参数资料
| 型号： | DS1862AB+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 15/42页 |
| 文件大小： | 0K |
| 描述： | IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 126 |
| 类型： | 激光二极管控制器（光纤） |
| 数据速率： | 10Gbps |
| 通道数： | 7 |
| 电源电压： | 2.9 V ~ 5.5 V |
| 电流 - 电源： | 3mA |
| 工作温度： | -40°C ~ 100°C |
| 封装/外壳： | 25-TFBGA，CSPBGA |
| 供应商设备封装： | 25-BGA（5x5） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
XFP Laser Control and Digital Diagnostic IC
Detailed Description
The DS1862A’s block diagram is described in detail
within the following sections and memory map/memory
description.
Automatic Power Control (APC)
The DS1862A’s APC is accomplished by closed-loop
adjustment of the bias current (BIASSET) until the feed-
back current (BMD) from a photodiode matches the
value determined by the APC registers. The relation-
ship between the APC register and I BMD is given by:
I BMD = 5.859μA x APC C <7:0> +
(1.464μA x APC F <1:0>)
where APC C <7:0> is the 8-bit value in Table 04h, Byte
84h that controls the coarse BMD current, and
APC F <1:0> is the 2-bit value that controls the fine BMD
current.
The BMD pin appears as a voltage source in series
with two resistors. The overall equivalent resistance of
the BMD input pin can be closely approximated by the
into steady state. The DS1862A is designed to support
loop gains of 1/20 to 10.
On power-up, the BMD current ramps up to the previ-
ously saved current setting in EEPROM APC registers.
While operating, the DS1862A monitors the BMD cur-
rent. If it begins to deviate from the desired (set) I BMD
value, the current on the BIASSET pin is again adjusted
to compensate.
Extinction Ratio Control
Lookup Table (LUT)
The DS1862A uses a temperature indexed lookup table
(LUT) to control the extinction ratio. The MODSET pin is
capable of sinking current based on the 8-bit binary value
that is controlling it. The DS1862A also features a user-
configurable current range to increase extinction ratio
resolution. Five current ranges, as described in Table 1,
are available to control the current entering MODSET.
Table 1. Selectable Current Ranges for
plot in Figure 8. The voltage that appears on the BMD
pin, assuming no external current load, is 1.2V if BMD
is in sink-current mode (SRC_SINK_B = 0) or 2.0V if
BMD is set to source current (SRC_SINK_B = 1). This
allows the photodiode to be referenced to either V CC3
or GND. When the control loop is at steady state, the
BMD current setting matches the current that is mea-
sured by the I BMD voltage across the internal resis-
tance. During a transient period, the DS1862A adjusts
the current drive on the BIASSET pin to bring the loop
BMD RESISTANCE vs. BMD SUPPLY CURRENT
600
584
565
546
MODSET
LUT CURRENT RANGE
TABLE 04h, BYTE 86h<2:0>
000
001
010
011
100
I BMD
VOLTAGE
CURRENT RANGE
(μA)
0 to 75
0 to 150
0 to 300
0 to 600
0 to 1200
527
508
R BMD
BMD
489
470
0
V BMD
NOTE: V BMD IS
CONTROLLED BY THE
SRC_SINK_B BIT IN
TABLE 04h.
0
0.25
0.50
0.75
1.00
1.25
1.50
I BMD (mA)
Figure 8. Approximate Model of the BMD Input
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| DS1862B+T&R | IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1873T+ | IC CTLR SFP+ ANLG LDD 28-TQFN |
| DS1874T+ | IC CTLR SFP+ ANLG LDD 28-TQFN |
| DS2129S+T&R | IC REGULATOR SCSI 16-SOIC |
| DS2438Z+T&R | IC MONITOR SMART BATTERY 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1862AB+ | 功能描述:激光驱动器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862AB+T&R | 制造商:Maxim Integrated Products 功能描述:XFP LASER CONTROL 25CSBGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1862AB+T&R | 功能描述:激光驱动器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862AB+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC |
| DS1862B | 功能描述:激光驱动器 RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。