参数资料
| 型号： | DS2430A+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/19页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 256BIT TO92-3 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 256（32 x 8） |
| 接口： | 1 线 串行 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | TO-226-3、TO-92-3（TO-226AA）成形引线 |
| 供应商设备封装： | TO-92-3 |
| 包装： | 带卷 (TR) |
DS2430A
Slave-to-Master
A Read-data time slot begins like a Write-1 time slot. The voltage on the data line must remain below
V TL until the read low time t RL is expired. During the t RL window, when responding with a 0, the
DS2430A starts pulling the data line low; its internal timing generator determines when this pulldown
ends and the voltage starts rising again. When responding with a 1, the DS2430A does not hold the data
line low at all, and the voltage starts rising as soon as t RL is over.
The sum of t RL + δ (rise time) on one side and the internal timing generator of the DS2430A on the other
side define the master sampling window (t MSRMIN to t MSRMAX ) in which the master must perform a read
from the data line. For the most reliable communication, t RL should be as short as permissible, and the
master should read close to but no later than t MSRMAX . After reading from the data line, the master must
wait until t SLOT is expired. This guarantees sufficient recovery time t REC for the DS2430A to get ready for
the next time slot. Note that t REC specified herein applies only to a single DS2430A attached to a 1-Wire
line. For multidevice configurations, t REC must be extended to accommodate the additional 1-Wire device
input capacitance. Alternatively, an interface that performs active pullup during the 1-Wire recovery time
such as the DS2482-x00 or DS2480B 1-Wire line drivers can be used.
IMPROVED NETWORK BEHAVIOR (SWITCHPOINT HYSTERESIS)
In a 1-Wire environment, line termination is possible only during transients controlled by the bus master
(1-Wire driver). 1-Wire networks, therefore, are susceptible to noise of various origins. Depending on the
physical size and topology of the network, reflections from end points and branch points can add up, or
cancel each other to some extent. Such reflections are visible as glitches or ringing on the 1-Wire
communication line. Noise coupled onto the 1-Wire line from external sources can also result in signal
glitching. A glitch during the rising edge of a time slot can cause a slave device to lose synchronization
with the master and, consequently, result in a Search ROM command coming to a dead end or cause a
device-specific function command to abort. For better performance in network applications, the
DS2430A uses a new 1-Wire front end, which makes it less sensitive to noise.
The 1-Wire front end of the DS2430A differs from traditional slave devices in three characteristics.
1) There is additional low-pass filtering in the circuit that detects the falling edge at the beginning of a
time slot. This reduces the sensitivity to high-frequency noise.
2) There is a hysteresis at the low-to-high switching threshold V TH . If a negative glitch crosses V TH but
does not go below V TH - V HY , it will not be recognized (Figure 11, Case A)..
3) There is a time window specified by the rising edge hold-off time t REH during which glitches are
ignored, even if they extend below V TH - V HY threshold (Figure 11, Case B, t GL < t REH ). Deep voltage
droops or glitches that appear late after crossing the V TH threshold and extend beyond the t REH
window cannot be filtered out and are taken as the beginning of a new time slot (Figure 11, Case C,
t GL ≥ t REH ).
Devices that have the parameters V HY , and t REH specified in their electrical characteristics use the
improved 1-Wire front end.
V PUP
NOISE SUPPRESSION SCHEME Figure 11
t REH
V TH
t REH
V HY
0V
Case A
Case B
t GL
Case C
t GL
14 of 19
相关PDF资料 |
PDF描述 |
|---|---|
| AYF534865 | CONN SOCKET FPC 0.5MM 48POS SMD |
| DS2502G+U | IC ADD-ONLY MEMORY 1KB SFN |
| DS2502G+T&R | IC OTP 1KBIT 2SFN |
| DS2502P+T&R | IC OTP 1KBIT 6TSOC |
| DS2502+T&R | IC OTP 1KBIT TO92-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2430AV | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:256-Bit 1-Wire EEPROM |
| DS2430AX | 功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| DS2430AX#T&R | 功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| DS2430AX#U | 功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| DS2430AX-S | 功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。