- 您现在的位置：买卖IC网 > PDF目录378591 > DS26503 (Maxim Integrated Products, Inc.) T1/E1/J1/64KCC BITS Element PDF资料下载
参数资料
| 型号： | DS26503 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | T1/E1/J1/64KCC BITS Element |
| 中文描述： | T1/E1/J1 BITS单元 |
| 文件页数： | 30/123页 |
| 文件大小： | 995K |
| 代理商： | DS26503 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页
DS26503 T1/E1/J1 BITS Element
30 of 123
7. PROCESSOR INTERFACE
The DS26503 is controlled via a nonmultiplexed (BIS[1:0] = 01) or a multiplexed (BIS[1:0] = 00)
parallel bus. There is also a serial bus mode option, as well as a hardware mode of operation. The bus
interface type is selected by BIS1 and BIS0 as shown in
Table 7-1
.
Table 7-1. Port Mode Select
BIS1
0
0
1
1
BIS0
0
1
0
1
PORT MODE
Parallel Port Mode (Multiplexed)
Parallel Port Mode (Nonmultiplexed)
Serial Port Mode (SPI)
Hardware Mode
7.1 Parallel Port Functional Description
In parallel mode, the DS26503 can operate with either Intel or Motorola bus timing configurations. If the
BTS pin is tied low, Intel timing will be selected; if tied high, Motorola timing will be selected. All
Motorola bus signals are listed in parentheses (). See the timing diagrams in the
AC Electrical
Characteristics
section for more details.
7.2 SPI Serial Port Interface Functional Description
A serial SPI bus interface is selected when bus select is 10 (BIS[1:0] = 10). In this mode, a master/slave
relationship is enabled on the serial port with three signal lines (SCK, MOSI, and MISO) and a chip
select (
CS
), with the DS26503 acting as the slave. Port read/write timing is not related to the system
read/write timing, thus allowing asynchronous, half-duplex operation. See the
AC Electrical
Characteristics
section for the AC timing characteristics of the serial port.
7.2.1 Clock Phase and Polarity
Clock Phase and Polarity are selected by the CPHA and CPOL pins. The slave device should always be
configured to match the bus master. See the
SPI Serial Port Mode
section for detailed functional timing
diagrams.
7.2.2 Bit Order
The most significant bit (MSB) of each byte is transmitted first.
7.2.3 Control Byte
The bus master will transmit two control bytes following a chip select to a slave device. The MSB will be
a R/
W
bit (1=read, 0=write). The next 6 bits will be padded with 0s. The LSB of the first byte will be
A[7]. The second control byte will be the address bits (A[6:0]) of the target register, followed by a Burst
bit in the LSB position (1=Burst, 0=Non-burst).
7.2.4 Burst Mode
The last bit of the second control byte (LSB) is the Burst mode bit. When the Burst bit is enabled (set to
1) and a read operation is performed, the register address is automatically incremented after the LSB of
the previous byte read to the next register address. Data will be available on the next clock edge following
the LSB of the previous byte read. When the Burst bit is enabled (set to 1) and a write operation is
performed, the register address will be automatically incremented to the next byte boundary following the
LSB of the previous register write, and 8 more data bits will be expected on the serial bus. Burst accesses
相关PDF资料 |
PDF描述 |
|---|---|
| DS26LV3 | 16 AMP LOW PROFILE POWER RELAY |
| DS2703 | SHA-1 Battery Pack Authentication IC |
| DS2703U | SHA-1 Battery Pack Authentication IC |
| DS2703UR | SHA-1 Battery Pack Authentication IC |
| DS2703UT | SHA-1 Battery Pack Authentication IC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS26503_07 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:T1/E1/J1 BITS Element |
| DS26503DK | 功能描述:时钟和定时器开发工具 DS26503 Dev Kit RoHS:否 制造商:Texas Instruments 产品:Evaluation Modules 类型:Clock Conditioners 工具用于评估:LMK04100B 频率:122.8 MHz 工作电源电压:3.3 V |
| DS26503L | 功能描述:计时器和支持产品 E1-T1-J1 Bits Element RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| DS26503L+ | 功能描述:计时器和支持产品 E1-T1-J1 Bits Element RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| DS26503LN | 功能描述:计时器和支持产品 E1-T1-J1 Bits Element RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。