参数资料
型号: DS26524GNA5+
厂商: Maxim Integrated Products
文件页数: 202/273页
文件大小: 0K
描述: IC TXRX T1/E1/J1 QUAD 256-CSBGA
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 90
类型: 线路接口装置(LIU)
驱动器/接收器数: 4/4
规程: T1/E1/J1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 256-LBGA,CSBGA
供应商设备封装: 256-CSBGA(17x17)
包装: 托盘
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页当前第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页第223页第224页第225页第226页第227页第228页第229页第230页第231页第232页第233页第234页第235页第236页第237页第238页第239页第240页第241页第242页第243页第244页第245页第246页第247页第248页第249页第250页第251页第252页第253页第254页第255页第256页第257页第258页第259页第260页第261页第262页第263页第264页第265页第266页第267页第268页第269页第270页第271页第272页第273页
DS26524 Quad T1/E1/J1 Transceiver
34 of 273
8.8.1.7 Mapping E1 Channels onto a 1.544MHz Backplane
The user can use the RSCLKM bit (RIOCR.4) to enable the receive elastic store to operate with a 1.544MHz
backplane (24 channels / frame + F-bit). In this mode the user can choose which of the E1 time slots will be
ignored (not transmitted onto RSER) by programming the Receive Blank Channel Select registers
(RBCS1:RBCS4). A logic 1 in the associated bit location causes the elastic store to ignore the incoming E1 data for
that channel. Typically the user will want to program eight channels to be ignored. The default (power-up)
configuration will ignore channels 25 to 32, so that the first 24 E1 channels are mapped into the 24 channels of the
1.544MHz backplane. In this mode the F-bit location at RSER is always set to 1.
For example, if the user wants to ignore E1 time slots 0 (channel 1) and TS16 (channel 17), the RBCS1:RBCS4
registers would be programmed as follows:
RBCS1 = 01h
RBCS2 = 00h
RBCS3 = 01h
RBCS4 = FCh
8.8.2 IBO Multiplexer
The Interleaved Bus Operation (IBO) multiplexer is used in conjunction with the IBO function located within each
framer/formatter block (controlled by the RIBOC and TIBOC registers). When enabled, the IBO multiplexer
simplifies user interface by connecting bus signals internally. The IBO multiplexer eliminates the need for ganged
external wiring and tri-state output drivers on the RSER and RSIG pins. This option provides a more controlled,
cleaner, and lower power mode of operation.
Note that the channel block signals TCHBLK and RCHBLK are output at the rate of the of IBO selection. Hence, a
4.096MHz IBO would have the channel blocks (if programmed active at the rate of 4.096MHz). The particular
blocking channel would be active for a duration of the channel if programmed.
The DS26524 also supports the traditional mode of IBO operation by allowing complete access to individual
framers, and tri-stating the RSER and RSIG pins at the appropriate times for external bus wiring. This mode of
operation is enabled per framer in the associated RIBOC and TIBOC registers, while leaving the IBO multiplexer is
disabled (IBOMS0 = 0 and IBOMS1 = 0).
Figure 8-3, Figure 8-4, and Figure 8-5 show the equivalent internal circuit for each IBO mode. Table 8-4 describes
the pin function changes for each mode of the IBO multiplexer.
Table 8-4. Registers Related to the IBO Multiplexer
REGISTER
FRAMER
ADDRESSES
FUNCTION
Global Transceiver Control Register 1
0F0h
This is a global register for all four framers. It can be
used to specify ganged operation for the IBO.
Receive Interleave Bus Operation
Control Register (RIBOC)
088h
This register can be used for control of how many
framers and the corresponding speed for the IBO
links for the receiver.
Transmit Interleave Bus Operation
Control Register (TIBOC)
188h
This register can be used for control of how many
framers and the corresponding speed for the IBO
links for the transmitter.
Note: The addresses shown are for Framer 1. Addresses for Framers 2 to 4 can be calculated by using the following: Framer n = (Framer 1
address + (n - 1) x 200h), where n = 2 to 4 for Framers 2 to 4.
相关PDF资料
PDF描述
DS26528GNA5+ IC TXRX T1/E1/J1 OCT 256-CSBGA
DS26900LN+ IC JTAG MUX/SWITCH 144-LQFP
DS275E/T&R IC TXRX LINE-PWR RS232 14-TSSOP
DS276S IC TXRX LOW POWER RS-232 8-SOIC
DS2890P-000+T&R IC POT DIGITAL 1-WIRE 100K 6TSOC
相关代理商/技术参数
参数描述
DS26524GNA5+ 功能描述:网络控制器与处理器 IC 4-Port E1/T1/J1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS26528 功能描述:网络控制器与处理器 IC 8-Port E1/T1/J1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS26528_07 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Octal T1/E1/J1 Transceiver
DS26528DK 功能描述:网络开发工具 DS26528 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V
DS26528G 功能描述:网络控制器与处理器 IC 8-Port E1/T1/J1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray