参数资料
| 型号： | DS3911T+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC DAC 10BIT I2C QUAD 14TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 位数： | 10 |
| 数据接口： | I²C，串行 |
| 转换器数目： | 4 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 1.74W |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-TDFN-EP（3x5） |
| 包装： | 管件 |
| 输出数目和类型： | 4 电压，单极 |
| 采样率（每秒）： | * |
DS3911
Temperature-Controlled, Nonvolatile,
I2C Quad DAC
14
Maxim Integrated
bytes, after the last address counter position of FFh
is accessed, the address counter automatically wraps
back to the first location, 00h. Read operations can
continue indefinitely.
I2C LUT Lockout
Both the I2C port and the LUT controller have access to
the LUTs. To prevent bus/data contention, the LUT con-
troller goes into a wait state instead of accessing the LUT
if the I2C port is active. Register updates and memory
access are briefly described below.
Afteravoltageortemperatureconversioncompletes
or the TINDEX register is calculated, the results are
loaded into a shadow SRAM for the associated regis-
ter by a backdoor that is not seen by the I2C port. The
value is pushed forward to the SRAM cell seen by the
I2C port at a later state. It is not pushed if the I2C port
is active.
AfterTINDEX is calculated and loaded into the shad-
ow SRAM, the LUT controller goes into a round-robin
loop where it updates the VCC VALUE, TEMP VALUE,
and TINDEX registers, reads the DAC OFFSET and
DAC LUT, performs the calculation, and loads the
result into the DAC VALUE register. This process is
where contention could occur. As such, the state
machine waits until I2C is inactive before performing
this process. If the I2C port were to become active
for a long time period, the temperature compensation
does not run.
Memory Description
The device’s internal memory consists of both volatile
and nonvolatile registers located in Lower Memory and
four separate memory tables (Upper Memory), as shown
in Figure 8.
The Lower Memory is addressed from 00h–7Fh. Lower
Memory contains temperature reading, VCC reading,
status bits, control registers, table select bits, and all four
The Upper Memory consists of the following four memory
tables. The table select bits, TS[3:0], determine which
table is currently accessible through I2C at memory loca-
tion 80h–FFh.
Table 04h contains a nonvolatile temperature-indexed
DAC0 LUT and DAC0 OFFSET register designed to
hold the pulse-density modulation profile for DAC0.
Table 05h contains a nonvolatile temperature-indexed
DAC1 LUT and DAC1 OFFSET register designed to
hold the pulse-density modulation profile for DAC1.
Table 06h contains a nonvolatile temperature-indexed
DAC2 LUT and DAC2 OFFSET registers designed to
hold the pulse-density modulation profile for DAC2.
Table 07h contains a nonvolatile temperature-indexed
DAC3 LUT and DAC3 OFFSET registers designed to
hold the pulse-density modulation profile for DAC3.
Shadowed EEPROM
The DAC POR memory locations are actually shadowed
EEPROM and are controlled by the shadowed EEPROM
bit, SEE. By default, SEE is not set and these locations
act as ordinary EEPROM. By setting SEE these locations
function like SRAM cells, which allow an infinite num-
ber of write cycles without concern of wearing out the
EEPROM. This also eliminates the requirement for the
EEPROM write time, tW. Because changes made with
SEE enabled do not affect the EEPROM, these changes
are not retained through power cycles. The power-on
value is the last value written with SEE disabled. This
function can be used to speed up calibration and mini-
mize the number of EEPROM write cycles.
相关PDF资料 |
PDF描述 |
|---|---|
| DS4000KI/WBGA | IC OSC TCXO 19.44MHZ 24-BGA |
| DS4026S+WCN | IC OSC TCXO 25MHZ 16-SOIC |
| DS4100HW+ | IC OSC CLOCK 100MHZ 10LCCC |
| DS4266P+ | IC OSC CLOCK 266MHZ 10-LCCC |
| DS4302Z-020/T&R | IC DAC 5-BIT SGL 0-2.0V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3911T+ | 功能描述:ADC / DAC多通道 Fast APD Bias RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS3911T+T | 功能描述:ADC / DAC多通道 Fast APD Bias RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS3920 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Fast Current Mirror |
| DS3920_1112 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Fast Current Mirror |
| DS3920T-001+ | 功能描述:电流和电力监控器、调节器 Fast APD Bias RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。