- 您现在的位置：买卖IC网 > PDF目录10924 > DS4830T+T (Maxim Integrated Products)MCU 16B CTRL CALIBR MON 40-TQFN PDF资料下载
参数资料
| 型号： | DS4830T+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/30页 |
| 文件大小： | 0K |
| 描述： | MCU 16B CTRL CALIBR MON 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | MAXQ® |
| 核心处理器： | RISC |
| 芯体尺寸： | 16-位 |
| 速度： | 10MHz |
| 连通性： | 3 线，I²C，SPI |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 31 |
| 程序存储器容量： | 64KB（32K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 16 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 数据转换器： | A/D 18x13b，D/A 8x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 其它名称： | 90-4830T+TRL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
DS4830
Optical Microcontroller
23
Maxim Integrated
contains six peripheral modules, M0 to M5. An MIIR reg-
ister is implemented in modules M1 and M2. The MIIRs
are 16-bit read-only registers and all of them default to
all zeros on system reset. Once the module that causes
the interrupt is singled out, it can then be interrogated
for the specific interrupt source and software can take
appropriate action. Interrupts are evaluated by applica-
tion code allowing the definition of a unique interrupt
priority scheme for each application. Interrupt sources
are available from the watchdog timer, the ADC (includ-
ing sample/holds), fast comparators, the programmable
timer, SVM, the I2C-compatible master and slave inter-
face, 3-wire, master and slave SPI, and all GPIO pins.
I/O Port
The device allows for most inputs and outputs to function
as general-purpose input and/or output pins. There are
four ports: P0, P1, P2, and P6. Note that there is no port
corresponding to P6.7. The 7th bit of port 6 is nonfunc-
tional in all SFRs. Each pin is multiplexed with at least one
special function, such as interrupts, I/O pins, or JTAG
pins, etc.
The GPIO pins have Schmitt trigger receivers and full
CMOS output drivers and can support alternate functions.
The ports can be accessed through SFRs (PO[0,1,2,6],
PI[0,1,2,6], PD[0,1,2,6], EIE[0,1,2,6], EIF[0,1,2,6], and
EIES[0,1,2,6]) in modules 0 and 1, and each pin can be
individually configured. The pin is either high impedance
or a weak pullup when defined as an input, dependent on
the state of the corresponding bit in the output register. In
addition, each pin can function as external interrupt with
individual enable, flag and active edge selection, when
programmed as input.
The I/O port SFRs are accessed in module 0 and 1.
Detailed information regarding the GPIO block can be
found in the DS4830 User’s Guide.
DAC Outputs
The device provides eight 12-bit DAC outputs with multi-
ple reference options. An internal 2.5V reference is pro-
vided. There are also two selectable external references.
REFINA can be selected as the full-scale reference for
DAC0 to DAC3. REFINB can be selected as the full-scale
reference for DAC4 to DAC7. The DAC outputs are volt-
age buffered. Each DAC can be individually disabled and
put into a low-power power-down mode using DACCFG.
An external reset does not affect the DAC outputs.
If a DAC output is used during the lifetime of the DS4830,
the DAC must always be enabled to guarantee meeting
the INL and offset specifications. If a pin is used for a
DAC, it should be used only for the DAC function. The
pin’s function should not be switched between DAC and
PWM or switched between DAC and GPIO.
The DAC SFRs are accessed in module 4. Detailed
information regarding the DAC block can be found in the
DS4830 User’s Guide.
PWM Outputs
The device provides 10 independently configurable
PWM outputs. The PWM outputs are configured using
three SFRs: PWMCN, PWMDATA, and PWNSYNC. Using
PWMCN and PWMDATA, individual PWM channels can
be programmed for unique duty cycles (DCYCn), con-
figurations (PWMCFGn), and delays (PWMDLYn), where
n represents the PWM channel number.
The PWM clock can be obtained from the core clock,
peripheral clock, or an external clock, depending on
CLK_SEL bits programmed in individual PWMCFGn reg-
isters. The PWMCFGn register also enables/disables the
corresponding PWM output and selects the PWM polar-
ity. The user can set the duty cycle and the frequency
of each PWM output individually by configuring the cor-
responding DCYCn register and the PWMCFGn register.
The device allows 4-slot or 32-slot pulse spreading
options for each PWM channel. The PWM outputs can be
configured to be output on an alternate location using the
configuration register. PWMDLY is a 12-bit register used
for providing starting delay on different PWM channels,
and can be used to create multiphase PWM operation.
Different channels can be synchronized using the
PWMSYNC register. Doing so effectively brings the
channels in phase by restarting the channels that are to
be synchronized. An external reset does not affect the
PWM outputs.
The PWM SFRs are accessed in module 5. Detailed
information regarding the PWM block can be found in the
DS4830 User’s Guide.
相关PDF资料 |
PDF描述 |
|---|---|
| ISD5008PY | IC VOICE REC/PLAY 4-8MIN 28-DIP |
| VI-24H-CV-S | CONVERTER MOD DC/DC 52V 150W |
| 73S1209F-44IMR/F | IC SMART CARD READER 44-QFN |
| VE-B3Y-IV-F3 | CONVERTER MOD DC/DC 3.3V 99W |
| VI-243-CV-S | CONVERTER MOD DC/DC 24V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS485 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Low Power RS-485/RS-422 Multipoint Transceiver |
| DS485M | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| DS485M | 制造商:Texas Instruments 功能描述:RS485/422 LOW POWER TRNSCVR SOIC8 |
| DS485M/NOPB | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| DS485MX | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。