- 您现在的位置：买卖IC网 > PDF目录19361 > DSP56321VF200 (Freescale Semiconductor)IC DSP 24BIT 200MHZ 196-BGA PDF资料下载
参数资料
| 型号： | DSP56321VF200 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 10/84页 |
| 文件大小： | 0K |
| 描述： | IC DSP 24BIT 200MHZ 196-BGA |
| 标准包装： | 126 |
| 系列： | DSP56K/Symphony |
| 类型： | 定点 |
| 接口： | 主机接口，SSI，SCI |
| 时钟速率： | 200MHz |
| 非易失内存： | ROM（576 B） |
| 芯片上RAM： | 576kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 1.60V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 196-FBGA |
| 供应商设备封装： | 196-MAPBGA（15x15） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
DSP56321 Technical Data, Rev. 11
1-12
Freescale Semiconductor
Signals/Connections
1.9 Serial Communication Interface (SCI)
The SCI provides a full duplex port for serial communication with other DSPs, microprocessors, or peripherals
such as modems.
SCK1
PD3
Input/Output
Input or Output
Ignored Input
Serial Clock—Provides the serial bit rate clock for the ESSI. The SCK1 is a
clock input or output used by both the transmitter and receiver in synchronous
modes or by the transmitter in asynchronous modes.
Although an external serial clock can be independent of and asynchronous to
the DSP system clock, it must exceed the minimum clock cycle time of 6T (that
is, the system clock frequency must be at least three times the external ESSI
clock frequency). The ESSI needs at least three DSP phases inside each half of
the serial clock.
Port D 3—The default configuration following reset is GPIO input PD3. When
configured as PD3, signal direction is controlled through the Port D Direction
Register. The signal can be configured as an ESSI signal SCK1 through the Port
D Control Register.
SRD1
PD4
Input
Input or Output
Ignored Input
Serial Receive Data—Receives serial data and transfers the data to the ESSI
Receive Shift Register. SRD1 is an input when data is being received.
Port D 4—The default configuration following reset is GPIO input PD4. When
configured as PD4, signal direction is controlled through the Port D Direction
Register. The signal can be configured as an ESSI signal SRD1 through the
Port D Control Register.
STD1
PD5
Output
Input or Output
Ignored Input
Serial Transmit Data—Transmits data from the Serial Transmit Shift Register.
STD1 is an output when data is being transmitted.
Port D 5—The default configuration following reset is GPIO input PD5. When
configured as PD5, signal direction is controlled through the Port D Direction
Register. The signal can be configured as an ESSI signal STD1 through the Port
D Control Register.
Notes:
1.
In the Stop state, the signal maintains the last state as follows:
If the last state is input, the signal is an ignored input.
If the last state is output, these lines have weak keepers that maintain the last output state even if the drivers are tri-stated.
2.
The Wait processing state does not affect the signal state.
Table 1-13.
Serial Communication Interface
Signal Name
Type
State During
Reset1,2
Signal Description
RXD
PE0
Input
Input or Output
Ignored Input
Serial Receive Data—Receives byte-oriented serial data and transfers it to the
SCI Receive Shift Register.
Port E 0—The default configuration following reset is GPIO input PE0. When
configured as PE0, signal direction is controlled through the Port E Direction
Register. The signal can be configured as an SCI signal RXD through the Port E
Control Register.
TXD
PE1
Output
Input or Output
Ignored Input
Serial Transmit Data—Transmits data from the SCI Transmit Data Register.
Port E 1—The default configuration following reset is GPIO input PE1. When
configured as PE1, signal direction is controlled through the Port E Direction
Register. The signal can be configured as an SCI signal TXD through the Port E
Control Register.
Table 1-12.
Enhanced Serial Synchronous Interface 1 (Continued)
Signal Name
Type
State During
Reset1,2
Signal Description
相关PDF资料 |
PDF描述 |
|---|---|
| IRS2158DSPBF | IC DVR HALF BRIDGE 600V 16-SOIC |
| IRS2166DSPBF | IC PFC/BALLAST/HALF BRDG 16-SOIC |
| TPSC686M006R0150 | CAP TANT 68UF 6.3V 20% 2312 |
| RBM10DRKI | CONN EDGECARD 20POS DIP .156 SLD |
| EP1K30FC256-3 | IC ACEX 1K FPGA 30K 256-FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DSP56321VF200R2 | 功能描述:数字信号处理器和控制器 - DSP, DSC 321 MAP 200MHZ T&R RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56321VF220 | 功能描述:数字信号处理器和控制器 - DSP, DSC 220Mhz/440MMACS 220Mhz EFCOP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56321VF240 | 功能描述:数字信号处理器和控制器 - DSP, DSC 240Mhz/480MMACS 240Mhz EFCOP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56321VF275 | 功能描述:数字信号处理器和控制器 - DSP, DSC 275Mhz/550MMACS 275Mhz EFCOP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56321VL200 | 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP PBFREE RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。