参数资料
| 型号： | EFM32TG210F32 |
| 厂商： | Energy Micro |
| 文件页数： | 20/136页 |
| 文件大小： | 0K |
| 描述： | MCU 32BIT 32KB FLASH 32-QFN |
| 特色产品： | EFM32 Tiny Gecko |
| 标准包装： | 1 |
| 系列： | Tiny Gecko |
| 核心处理器： | ARM? Cortex?-M3 |
| 芯体尺寸： | 32-位 |
| 速度： | 32MHz |
| 连通性： | EBI/EMI，I²C，IrDA，智能卡，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，DMA，POR，PWM，WDT |
| 输入/输出数： | 24 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 4K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 3.8 V |
| 数据转换器： | A/D 4x12b，D/A 1x12b |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-VQFN 裸露焊盘 |
| 包装： | 标准包装 |
| 其它名称： | 914-1034-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
...the world's most energy friendly microcontrollers
2011-02-04 - d0002_Rev1.00
116
www.energymicro.com
Bits
Name
Function
0 = MPU is disabled during hard fault, NMI, and FAULTMASK handlers, regardless of the value
of the ENABLE bit
1 = the MPU is enabled during hard fault, NMI, and FAULTMASK handlers.
When the MPU is disabled, if this bit is set to 1 the behavior is Unpredictable.
[0]
ENABLE
Enables the MPU:
0 = MPU disabled
1 = MPU enabled.
When ENABLE and PRIVDEFENA are both set to 1:
For privileged accesses, the default memory map is as described in Section 2.2 (p. 14) . Any access
by privileged software that does not address an enabled memory region behaves as defined by the
default memory map.
Any access by unprivileged software that does not address an enabled memory region causes a
memory management fault.
XN and Strongly-ordered rules always apply to the System Control Space regardless of the value of
the ENABLE bit.
When the ENABLE bit is set to 1, at least one region of the memory map must be enabled for the system
to function unless the PRIVDEFENA bit is set to 1. If the PRIVDEFENA bit is set to 1 and no regions
are enabled, then only privileged software can operate.
When the ENABLE bit is set to 0, the system uses the default memory map. This has the same memory
attributes as if the MPU is not implemented, see Table 2.11 (p. 16) . The default memory map applies
to accesses from both privileged and unprivileged software.
When the MPU is enabled, accesses to the System Control Space and vector table are always permitted.
Other areas are accessible based on regions and whether PRIVDEFENA is set to 1.
Unless HFNMIENA is set to 1, the MPU is not enabled when the processor is executing the handler for
an exception with priority –1 or –2. These priorities are only possible when handling a hard fault or NMI
exception, or when FAULTMASK is enabled. Setting the HFNMIENA bit to 1 enables the MPU when
operating with these two priorities.
4.5.3 MPU Region Number Register
The RNR selects which memory region is referenced by the RBAR and RASR registers. See the register
summary in Table 4.38 (p. 114) for its attributes. The bit assignments are:
Reserved
31
8 7
0
REGION
Table 4.41. RNR bit assignments
Bits
Name
Function
[31:8]
-
Reserved.
[7:0]
REGION
Indicates the MPU region referenced by the RBAR and RASR registers.
The MPU supports 8 memory regions, so the permitted values of this field are 0-7.
Normally, you write the required region number to this register before accessing the RBAR or RASR.
However you can change the region number by writing to the RBAR with the VALID bit set to 1, see
Section 4.5.4 (p. 117) . This write updates the value of the REGION field.
相关PDF资料 |
PDF描述 |
|---|---|
| MPC565CZP56 | IC MPU 32BIT IM FLASH 388-PBGA |
| C8051F587-IQ | IC 8051 MCU 96K FLASH 32-QFP |
| MC68HC11F1CFN2 | IC MCU 512 EEPROM 2MHZ 68-PLCC |
| MC68HC11F1CFN3 | IC MCU 512 EEPROM 3MHZ 68-PLCC |
| MC68HC11F1CFN4 | IC MCU 512 EEPROM 4MHZ 68-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EFM32TG210F32-QFN32 | 制造商:Energy Micro AS 功能描述:TINY GECKO MCU - Tape and Reel 制造商:Energy Micro AS 功能描述:TINY GECKO MCU - Cut TR (SOS) 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 32KB FLASH 32QFN |
| EFM32TG210F32-QFN32T | 制造商:Energy Micro AS 功能描述:32 BIT ARM MPU, TINY GECKO - Trays |
| EFM32TG210F32-QFN32-T | 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 32KB FLASH 32QFN |
| EFM32-TG210F32-SK | 功能描述:IC MICRO KIT GECKO 32QFN RoHS:是 类别:套件 >> 半导体产品 - IC 元件分类 系列:Tiny Gecko 其它有关文件:NXPLOGIC2-KIT-ND Contents 标准包装:1 系列:74AUP 套件类型:逻辑 值:180 件 - 18 种值各 10 件 包装:- 安装类型:表面贴装 包括封装:6-XSON，8-XSON，8-XQFN 产品目录页面:2653 (CN2011-ZH PDF) 工具箱内容:(10) 568-4391-1-ND - IC GATE MULT-FUNC CONFIG 6-XSON(10) 568-4390-1-ND - IC CONFIG MULT-FUNC GATE 6-XSON(10) 568-4389-1-ND - IC GATE DUAL FUNCTION 8-XSON(10) 568-4388-1-ND - IC GATE DUAL FUNCTION 8-XQFN(10) 568-4387-1-ND - IC F-F D-TYPE POS EDGE 8-XSON(10) 568-4386-1-ND - IC F-F D-TYPE POS EDGE 8-XQFN(10) 568-4385-1-ND - IC CONFIG MULTI-FUNC GATE 6-XSON(10) 568-4384-1-ND - IC EX-OR GATE 3-IN 6-XSON(10) 568-4383-1-ND - IC F-F D-TYPE POS EDGE 6-XSON(10) 568-4382-1-ND - IC LATCH D-TYPE 6-XSON更多... 其它名称:NXPLOGIC2-KIT |
| EFM32TG210F32-T | 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 32KB FLASH 32QFN |
发布紧急采购，3分钟左右您将得到回复。