参数资料
| 型号： | EPC16UC88AA |
| 厂商： | Altera |
| 文件页数： | 18/36页 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 16MBIT 88-UBGA |
| 标准包装： | 80 |
| 系列： | EPC |
| 可编程类型： | 系统内可编程 |
| 存储容量： | 16Mb |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 88-LFBGA |
| 供应商设备封装： | 88-UBGA（11x8） |
| 包装： | 托盘 |
| 其它名称： | 544-1373 EPC16UC88AA-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Power-On Reset
Page 25
Enhanced Configuration (EPC) Devices Datasheet
January 2012
Altera Corporation
Power-On Reset
The POR circuit keeps the system in reset until power-supply voltage levels have
stabilized. The POR time consists of the VCC ramp time and a user-programmable
POR delay counter. When the supply is stable and the POR counter expires, the POR
circuit releases the OE pin. The POR time can be further extended by an external
device by driving the OE pin low.
1 Do not execute JTAG or ISP instructions until POR is complete.
The EPC device supports a programmable POR delay setting. You can set the POR
delay to the default 100-ms setting or reduce the POR delay to 2 ms for systems that
require fast power-up. The PORSEL input pin controls this POR delay—a logic-high
level selects the 2-ms delay, while a logic-low level selects the 100-ms delay.
The EPC device enters reset under the following conditions:
■
The POR reset starts at initial power-up during VCC ramp-up or if VCC drops
below the minimum operating condition anytime after VCC has stabilized
■
The FPGA initiates reconfiguration by driving nSTATUS low, which occurs if the
FPGA detects a CRC error or if the FPGA’s nCONFIG input pin is asserted
■
The controller detects a configuration error and asserts OE to begin reconfiguration
of the Altera FPGA (for example, when CONF_DONE stays low after all configuration
data has been transmitted)
EXCLK
Input
Optional external clock input pin that can be used to generate the configuration
clock (DCLK).
When an external clock source is not used, connect this pin to a valid logic level
(high or low) to prevent a floating-input buffer. If EXCLK is used, toggling the
EXCLK
input pin after the FPGA enters user mode will not effect the EPC device
operation.
PORSEL
Input
This pin selects a 2-ms or 100-ms POR counter delay during power up. When
PORSEL
is low, POR time is 100 ms. When PORSEL is high, POR time is 2 ms.
This pin must be connected to a valid logic level.
TM0
Input
For normal operation, this test pin must be connected to GND.
TM1
Input
For normal operation, this test pin must be connected to VCC.
Table 10. JTAG Interface Pins and Other Required Controller Pins (Part 2 of 2)
Pin Name
Pin Type
Description
相关PDF资料 |
PDF描述 |
|---|---|
| EPCS16SI16N | IC CONFIG DEVICE 16MBIT 16-SOIC |
| EPF10K10AQI208-3 | IC FLEX 10KA FPGA 10K 208-PQFP |
| EPF10K200EBC600-1 | IC FLEX 10KE FPGA 200K 600-BGA |
| EPF6024AQI208-3 | IC FLEX 6000 FPGA 24K 208-PQFP |
| EPF81500AQC240-2 | IC FLEX 8000A FPGA 16K 240-PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPC16UC88N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC16UI88AA | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC16UI88N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC16XXX | 制造商:ALTERA 制造商全称:Altera Corporation 功能描述:2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC17 | 制造商:TDK 制造商全称:TDK Electronics 功能描述:Ferrite Cores For Power Supply and Signal Transformer EPC Cores |
发布紧急采购，3分钟左右您将得到回复。