参数资料
| 型号： | EPC16UC88AA |
| 厂商： | Altera |
| 文件页数： | 2/36页 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 16MBIT 88-UBGA |
| 标准包装： | 80 |
| 系列： | EPC |
| 可编程类型： | 系统内可编程 |
| 存储容量： | 16Mb |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 88-LFBGA |
| 供应商设备封装： | 88-UBGA（11x8） |
| 包装： | 托盘 |
| 其它名称： | 544-1373 EPC16UC88AA-ND |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Page 10
Functional Description
Enhanced Configuration (EPC) Devices Datasheet
January 2012
Altera Corporation
Fast Passive Parallel Configuration
Stratix series and APEX II devices can be configured using the EPC device in the FPP
configuration mode. In this mode, the EPC device sends a byte of data on the
DATA[7..0]
pins, which connect to the DATA[7..0] input pins of the FPGA, per DCLK
cycle. Stratix series and APEX II FPGAs receive byte-wide configuration data per DCLK
cycle. Figure 2 shows the EPC device in FPP configuration mode. In this figure, the
external flash interface is not used and hence most flash pins are left unconnected
(with the few noted exceptions).
f For more information about configuration interface connections including the pull-up
resistor values, supply voltages, and MSEL pin settings, refer to the configuration
chapter in the appropriate device handbook.
Figure 2. FPP Configuration
Notes to Figure 2:
(1) The VCC should be connected to the same supply voltage as the EPC device.
(2) The nINIT_CONF pin is available on EPC devices and has an internal pull-up resistor that is always active. This means an external pull-up
resistor is not required on the nINIT_CONF or nCONFIG signal. The nINIT_CONF pin does not need to be connected if its functionality is not
used. If nINIT_CONF is not used, nCONFIG must be pulled to VCC either directly or through a resistor.
(3) The EPC devices’ OE and nCS pins have internal programmable pull-up resistors. If internal pull-up resistors are used, external pull-up resistors
should not be used on these pins. The internal pull-up resistors are used by default in the Quartus II software. To turn off the internal pull-up
resistors, check the Disable nCS and OE pull-ups on configuration device option when generating programming files.
(4) For PORSEL, PGM[], and EXCLK pin connections, refer to Table 10 on page 24.
(5) In the 100-pin PQFP package, you must externally connect the following pins: C-A0 to F-A0, C-A1 to F-A1, C-A15 to F-A15, C-A16 to
F-A16
, and BYTE# to VCC. Additionally, you must make the following pin connections in both 100-pin PQFP and 88-pin UFBGA packages: C-RP#
to F-RP#, C-WE# to F-WE#, TM1 to VCC, TM0 to GND, and WP# to VCC.
(6) Connect the FPGA MSEL[] input pins to select the FPP configuration mode. For more information, refer to the configuration chapter in the
appropriate device handbook.
(7) To protect Intel Flash-based EPC devices content, isolate the VCCW supply from VCC. For more information, refer to “Intel Flash-Based EPC Device
EPC Device
DCLK
DATA[7..0]
OE
nCS
nINIT_CONF (2)
MSEL
DCLK
DATA[7..0]
nSTATUS
CONF_DONE
nCONFIG
VCC
GND
(3)
nCE
EXCLK
Stratix Series
or
APEX II Device
WE#C
RP#C
WP#
PORSEL
PGM[2..0]
TMO
WE#F
RP#F
A[20..0]
RY/BY#
CE#
OE#
DQ[15..0]
VCC
N.C.
BYTE# (5)
TM1
(3)
C-A0 (5)
C-A1 (5)
C-A15 (5)
C-A16 (5)
A0-F
A1-F
A15-F
A16-F
(1)
n
(6)
(1)
nCEO
N.C.
(4)
VCCW
VCC (7)
相关PDF资料 |
PDF描述 |
|---|---|
| EPCS16SI16N | IC CONFIG DEVICE 16MBIT 16-SOIC |
| EPF10K10AQI208-3 | IC FLEX 10KA FPGA 10K 208-PQFP |
| EPF10K200EBC600-1 | IC FLEX 10KE FPGA 200K 600-BGA |
| EPF6024AQI208-3 | IC FLEX 6000 FPGA 24K 208-PQFP |
| EPF81500AQC240-2 | IC FLEX 8000A FPGA 16K 240-PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPC16UC88N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC16UI88AA | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC16UI88N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPC16XXX | 制造商:ALTERA 制造商全称:Altera Corporation 功能描述:2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC17 | 制造商:TDK 制造商全称:TDK Electronics 功能描述:Ferrite Cores For Power Supply and Signal Transformer EPC Cores |
发布紧急采购，3分钟左右您将得到回复。