参数资料
| 型号： | EPCS16SI16N |
| 厂商： | Altera |
| 文件页数： | 15/40页 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 16MBIT 16-SOIC |
| 产品变化通告： | Product Discontinuation 01/31/2008 |
| 标准包装： | 49 |
| 系列： | EPCS |
| 可编程类型： | 系统内可编程 |
| 存储容量： | 16Mb |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
| 其它名称： | 544-1240-5 EPCS16SI16 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
Page 22
EPCS Device Memory Access
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Figure 11 shows the instruction sequence of the read bytes operation.
Fast Read Operation
The fast read operation code is b’0000 1011 and it lists the MSB first. You can select
the device by driving the nCS signal low. The fast read instruction code is followed by
a 3-byte address (A23-A0) and a dummy byte with each bit being latched-in during the
rising edge of the DCLK signal. Then, the memory contents at that address is shifted out
on DATA with each bit being shifted out at a maximum frequency of 40 MHz during
the falling edge of the DCLK signal.
The first addressed byte can be at any location. The address is automatically increased
to the next higher address after each byte of data is shifted out. Therefore, the whole
memory can be read with a single fast read instruction. When the highest address is
reached, the address counter rolls over to 000000h, allowing the read sequence to
continue indefinitely.
The fast read instruction is terminated by driving the nCS signal high at any time
during data output. Any fast read instruction is rejected during the erase, program, or
write operations without affecting the operation that is in progress.
Figure 11. Read Bytes Operation Timing Diagram
Notes to Figure 11:
(1) Address bit A[23] is a don't-care bit in the EPCS64 device. Address bits A[23..21] are don't-care bits in the EPCS16 device. Address bits
A[23..19]
are don't-care bits in the EPCS4 device. Address bits A[23..17] are don't-care bits in the EPCS1 device.
(2) For .rpd files, the read sequence shifts out the LSB of the data byte first.
nCS
DCLK
ASDI
DATA
0
1
2
3
4
5
6
7
8
9
10
28
29
30
31
32
33
34
35
36
37
38
39
Operation Code
24-Bit Address (1)
23
22
21
3
2
1
0
77
65
43
210
MSB
MSB (2)
High Impedance
DATA Out 1
DATA Out 2
相关PDF资料 |
PDF描述 |
|---|---|
| EPF10K10AQI208-3 | IC FLEX 10KA FPGA 10K 208-PQFP |
| EPF10K200EBC600-1 | IC FLEX 10KE FPGA 200K 600-BGA |
| EPF6024AQI208-3 | IC FLEX 6000 FPGA 24K 208-PQFP |
| EPF81500AQC240-2 | IC FLEX 8000A FPGA 16K 240-PQFP |
| EPM2210GF324C3 | IC MAX II CPLD 2210 LE 324-FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPCS16SI8N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 40 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPCS1N | 制造商:ALTERA 制造商全称:Altera Corporation 功能描述: |
| EPCS1SI8 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 1Mb 40 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPCS1SI8N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 1Mb 40 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPCS250 | 制造商:Electrolube 功能描述:COATING MASK PEELABLE 250 制造商:Electrolube 功能描述:COATING MASK, PEELABLE 250 |
发布紧急采购，3分钟左右您将得到回复。