参数资料
| 型号： | EPCS16SI16N |
| 厂商： | Altera |
| 文件页数： | 21/40页 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 16MBIT 16-SOIC |
| 产品变化通告： | Product Discontinuation 01/31/2008 |
| 标准包装： | 49 |
| 系列： | EPCS |
| 可编程类型： | 系统内可编程 |
| 存储容量： | 16Mb |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
| 其它名称： | 544-1240-5 EPCS16SI16 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
Page 28
Power and Operation
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Power and Operation
This section describes the power modes, power-on reset (POR) delay, error detection,
and initial programming state of the EPCS devices.
Power Mode
EPCS devices support active and standby power modes. When the nCS signal is low,
the device is enabled and is in active power mode. The FPGA is configured while the
EPCS device is in active power mode. When the nCS signal is high, the device is
disabled but remains in active power mode until all internal cycles are completed,
such as write or erase operations. The EPCS device then goes into standby power
mode. The ICC1 and ICC0 parameters list the VCC supply current when the device is in
active and standby power modes. For more information, refer to Table 21 on page 34.
Power-On Reset
During the initial power-up, a POR delay occurs to ensure the system voltage levels
have stabilized. During the AS configuration, the FPGA controls the configuration
and has a longer POR delay than the EPCS device.
f For more information about the POR delay time, refer to the configuration chapter in
the appropriate device handbook.
Error Detection
During the AS configuration with the EPCS device, the FPGA monitors the
configuration status through the nSTATUS and CONF_DONE pins. If an error condition
occurs, if the nSTATUS pin drives low or if the CONF_DONE pin does not go high, the
FPGA begins reconfiguration by pulsing the nSTATUS and nCSO signals, which controls
the chip select (nCS) pin on the EPCS device.
After an error, the configuration automatically restarts if the Auto-Restart Upon
Frame Error
option is turned on in the Quartus II software. If the option is turned off,
the system must monitor the nSTATUS signal for errors and then pulse the nCONFIG
signal low to restart configuration.
相关PDF资料 |
PDF描述 |
|---|---|
| EPF10K10AQI208-3 | IC FLEX 10KA FPGA 10K 208-PQFP |
| EPF10K200EBC600-1 | IC FLEX 10KE FPGA 200K 600-BGA |
| EPF6024AQI208-3 | IC FLEX 6000 FPGA 24K 208-PQFP |
| EPF81500AQC240-2 | IC FLEX 8000A FPGA 16K 240-PQFP |
| EPM2210GF324C3 | IC MAX II CPLD 2210 LE 324-FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPCS16SI8N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 16Mb 40 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPCS1N | 制造商:ALTERA 制造商全称:Altera Corporation 功能描述: |
| EPCS1SI8 | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 1Mb 40 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPCS1SI8N | 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 1Mb 40 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20 |
| EPCS250 | 制造商:Electrolube 功能描述:COATING MASK PEELABLE 250 制造商:Electrolube 功能描述:COATING MASK, PEELABLE 250 |
发布紧急采购，3分钟左右您将得到回复。