- 您现在的位置：买卖IC网 > PDF目录223750 > ES29BDS400ET-90RTGI (优先(苏州)半导体有限公司) 4Mbit(512Kx 8/256K x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | ES29BDS400ET-90RTGI |
| 厂商： | 优先(苏州)半导体有限公司 |
| 英文描述： | 4Mbit(512Kx 8/256K x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| 中文描述： | 的4Mb（512Kx 8/256K × 16），3.0伏的CMOS只，引导扇区闪存 |
| 文件页数： | 48/51页 |
| 文件大小： | 697K |
| 代理商： | ES29BDS400ET-90RTGI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页第51页
ES I
6
Rev.0B January 5, 2006
ES29LV400E
Excel Semiconductor inc.
Several device operational modes are provided in
the ES29LV400 device. Commands are used to ini-
tiate the device operations. They are latched and
stored into internal registers with the address and
data information needed to execute the device
operation.
The available device operational modes are listed
in Table 1 with the required inputs, controls, and the
resulting
outputs.
Each
operational
mode
is
described in further detail in the following subsec-
tions.
Read
The internal state of the device is set for the read
mode and the device is ready for reading array data
upon device power-up, or after a hardware reset. To
read the stored data from the cell array of the
device, CE# and OE# pins should be driven to VIL
while WE# pin remains at VIH. CE# is the power
control and selects the device. OE# is the output
control and gates array data to the output pins.
Word or byte mode of output data is determined by
the BYTE# pin. No additional command is needed
in this mode to obtain array data. Standard micro-
processor read cycles that assert valid addresses
on the device address inputs produce valid data on
the device data outputs. The device stays at the read
mode until another operation is activated by writing
commands into the internal command register. Refer
to the AC read cycle timing diagrams for further
details ( Fig. 16 ).
Word/Byte Mode Configuration ( BYTE# )
The device data output can be configured by BYTE#
into one of two modes : word and byte modes. If the
BYTE# pin is set at logic ‘1’, the device is configured
in word mode, DQ0 - DQ15 are active and controlled
by CE# and OE#. If the BYTE# pin is set at logic ‘0’,
the device is configured in byte mode, and only data
I/O pins DQ0 - DQ7 are active and controlled by CE#
and OE#. The data I/O pins DQ8 - DQ14 are tri-
stated, and the DQ15 pin is used as an input for the
LSB (A-1) address.
Standby Mode
When the device is not selected or activated in a
system, it needs to stay at the standby mode, in
which current consumption is greatly reduced with
outputs in the high impedance state.
DEVICE BUS OPERATIONS
相关PDF资料 |
PDF描述 |
|---|---|
| ES29BDS400FB-70RWCI | 4Mbit(512Kx 8/256K x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES29BDS400FT-70RWCI | 4Mbit(512Kx 8/256K x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES2BA | 2 A, 100 V, SILICON, RECTIFIER DIODE |
| ES3250402ATL | POWER/SIGNAL RELAY, 3PDT, MOMENTARY, 0.097A (COIL), 28VDC (COIL), 2716mW (COIL), 25A (CONTACT), 28VDC (CONTACT), PANEL MOUNT |
| ES52K1C05N-20.000MTR | TCXO, CLIPPED SINE OUTPUT, 20 MHz |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ES29BDS400ET-90TGI | 制造商:EXCELSEMI 制造商全称:EXCELSEMI 功能描述:16Mbit(2M x 8/1M x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES29BDS400F-12RTG | 制造商:EXCELSEMI 制造商全称:EXCELSEMI 功能描述:32Mbit(4M x 8/2M x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES29BDS400F-70WCI | 制造商:EXCELSEMI 制造商全称:EXCELSEMI 功能描述:32Mbit(4M x 8/2M x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES29BDS400FB-12RTG | 制造商:EXCELSEMI 制造商全称:EXCELSEMI 功能描述:32Mbit(4M x 8/2M x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
| ES29BDS400FB-12TG | 制造商:EXCELSEMI 制造商全称:EXCELSEMI 功能描述:16Mbit(2M x 8/1M x 16) CMOS 3.0 Volt-only, Boot Sector Flash Memory |
发布紧急采购，3分钟左右您将得到回复。