- 您现在的位置：买卖IC网 > PDF目录16569 > EVAL-AD2S1200SDZ (Analog Devices Inc)BOARD EVAL FOR AD2S1200 PDF资料下载
参数资料
| 型号： | EVAL-AD2S1200SDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD2S1200 |
| 标准包装： | 1 |
| 主要目的： | 接口，旋转变压至数字 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD2S1200 |
| 主要属性： | 图形用户界面（GUI） |
| 已供物品： | 板，CD，电源 |
AD2S1200
Rev. 0 | Page 9 of 24
PRINCIPLE OF OPERATION
The AD2S1200 operates on a Type II tracking closed-loop
principle. The output continually tracks the position of the
resolver without the need for external convert and wait states.
As the resolver moves through a position equivalent to the least
significant bit weighting, the output is updated by one LSB.
The converter tracks the shaft angle θ by producing an output
angle that is fed back and compared to the input angle θ, and
the resulting error between the two is driven towards 0 when
the converter is correctly tracking the input angle. To measure
the error, S3–S1 is multiplied by Cos and S2–S4 is multiplied
by Sin to give
4
2
3
1
0
S
to
S
Sin
Cos
t
Sin
E
S
to
S
Cos
Sin
t
Sin
E
φ
θ
ω
φ
θ
ω
×
The difference is taken, giving
)
(
0
φ
θ
φ
θ
×
ω
Sin
Cos
Sin
t
Sin
E
Equation 2.
This signal is demodulated using the internally generated
synthetic reference, yielding
)
(
0
φ
θ
φ
θ
Sin
Cos
Sin
E
Equation 3.
approximately equal to E0 (θ ) for small values of θ ,
where θ = angular error.
The value E0 (θ ) is the difference between the angular error
of the rotor and the converter’s digital angle output.
A phase-sensitive demodulator, integrators, and a compensation
filter form a closed-loop system that seeks to null the error
signal. When this is accomplished, equals the resolver angle θ
within the rated accuracy of the converter. A Type II tracking
loop is used so that constant velocity inputs can be tracked
without inherent error.
For more information about the operation of the converter, see
the Circuit Dynamics section.
FAULT DETECTION CIRCUIT
The AD2S1200 fault detection circuit will detect loss of resolver
signals, out of range input signals, input signal mismatch, or loss
of position tracking. In these cases, the position indicated by the
AD2S1200 may differ significantly from the actual shaft
position of the resolver.
Monitor Signal
The AD2S1200 generates a monitor signal by comparing the
angle in the position register to the incoming Sin and Cos
signals from the resolver. The monitor signal is created in a
similar fashion to the error signal described in the Principle of
Operation section. The incoming signals Sinθ and Cosθ are
multiplied by the Sin and Cos of the output angle, respectively,
and then added together as shown below:
φ
×
θ
×
+
φ
θ
×
=
Cos
A
Sin
x
Sin
A
Monitor
2
1
Equation 4.
Where A1 is the amplitude of the incoming Sin signal (A1 ×
Sinθ), A2 is the amplitude of the incoming Cos signal (A2 ×
Cosθ), θ is the resolver angle, and is the angle stored in the
position register. Note that Equation 4 is shown after demodula-
tion, with the carrier signal Sinωt removed. Also note that for
matched input signal (i.e., no-fault condition), A1 = A2.
When A1 = A2 and the converter is tracking (θ = ), the
monitor signal output has a constant magnitude of A1 (Monitor
= A1 × (Sin2 θ + Cos2 θ) = A1), independent of shaft angle.
When A1 ≠ A2, the monitor signal magnitude varies between
A1 and A2 at twice the rate of shaft rotation. The monitor signal
is used as described in the following sections to detect
degradation or loss of input signals.
Loss of Signal Detection
Loss of signal (LOS) is detected when either resolver input (Sin
or Cos) falls below the specified LOS Sin/Cos threshold by
comparing the monitor signal to a fixed minimum value. LOS is
indicated by both DOS and LOT latching as logic low outputs.
The DOS and LOT pins are reset to the no fault state by a rising
edge of SAMPLE. The LOS condition has priority over both the
DOS and LOT conditions, as shown in Table 4. LOS is indicated
within 45° of angular output error worst case.
相关PDF资料 |
PDF描述 |
|---|---|
| GEC10DRAI-S734 | CONN EDGECARD 20POS .100 R/A SLD |
| EBM25DCAI-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| H6MMS-5018M | DIP CABLE - HDM50S/AE50M/HDM50S |
| A3CCH-1618M | IDC CABLE - AKC16H/AE16M/AKC16H |
| GBC10DRAH-S734 | CONN EDGECARD 20POS .100 R/A SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD2S1205CBZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. |
| EVAL-AD2S1205SDZ | 功能描述:BOARD EVAL FOR AD2S1205 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD2S1210EDZ | 功能描述:BOARD EVAL AD2S1210 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| EVAL-AD4001FMCZ | 功能描述:EVAL BOARD FOR AD4001 制造商:analog devices inc. 系列:- 零件状态:在售 A/D 转换器数:1 位数:16 采样率（每秒）:2M 数据接口:SPI，DSP 输入范围:±VREF 不同条件下的功率（典型值）:20mW @ 2MSPS 使用的 IC/零件:AD4001 所含物品:板，电源 标准包装:1 |
| EVAL-AD421EB | 制造商:AD 制造商全称:Analog Devices 功能描述:Loop-Powered 4 mA to 20 mA DAC |
发布紧急采购，3分钟左右您将得到回复。