- 您现在的位置：买卖IC网 > PDF目录17075 > EVAL-AD5425EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD5425 PDF资料下载
参数资料
| 型号： | EVAL-AD5425EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/25页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD5425 |
| 产品培训模块： | DAC Architectures |
| 标准包装： | 1 |
| DAC 的数量： | 1 |
| 位数： | 8 |
| 采样率（每秒）： | 2.47M |
| 数据接口： | 串行 |
| 设置时间： | 15ns |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 125°C |
| 已供物品： | 板，CD |
| 已用 IC / 零件： | AD5425 |
| 相关产品： | AD5425YRMZ-REEL7-ND - IC DAC 8BIT MULTIPLYING 10MSOP AD5425YRMZ-REEL-ND - IC DAC 8BIT MULTIPLYING 10MSOP AD5425YRMZ-ND - IC DAC 8BIT MULTIPLYING 10MSOP AD5425YRM-REEL7-ND - IC DAC 8BIT MULTIPLYING 10-MSOP AD5425YRM-REEL-ND - IC DAC 8BIT MULTIPLYING 10-MSOP AD5425YRM-ND - IC DAC MULTIPLYING 8BIT 10-MSOP |
Data Sheet
AD5425
Rev. C | Page 17 of 24
ADDING GAIN
In applications where the output voltage is required to be
greater than VIN, gain can be added with an additional external
amplifier or it can be achieved in a single stage. It is important
to take into consideration the effect of temperature coefficients
of the thin film resistors of the DAC. Simply placing a resistor in
series with the RFB resistor causes mismatches in the temp-
erature coefficients and results in larger gain temperature
coefficient errors. Instead, the circuit of Figure 35 is a recom-
mended method of increasing the gain of the circuit. R1, R2,
and R3 should all have similar temperature coefficients, but
they need not match the temperature coefficients of the DAC.
This approach is recommended in circuits where gains of
greater than 1 are required.
Figure 35. Increasing the Gain of Current Output DAC
DACS USED AS A DIVIDER OR PROGRAMMABLE
GAIN ELEMENT
Current steering DACs are very flexible and lend themselves to
many different applications. If this type of DAC is connected as
the feedback element of an op amp and RFB is used as the input
resistor as shown in Figure 36, then the output voltage is
inversely proportional to the digital input fraction, D.
For D = 1 2n, the output voltage is
VOUT = VIN/D = VIN/(1 2n)
As D is reduced, the output voltage increases. For small values
of D, it is important to ensure that the amplifier does not satur-
ate and that the required accuracy is met. For example, an 8-bit
DAC driven with the Binary Code 0x10 (00010000), that is,
16 decimal, in the circuit of Figure 36, should cause the output
voltage to be 16 × VIN. However, if the DAC has a linearity
specification of ±0.5 LSB, then D can in fact have a weight
anywhere in the range 15.5/256 to 16.5/256. Therefore, the
possible output voltage is in the range of 15.5 VIN to 16.5 VIN—
an error of 3%, even though the DAC itself has a maximum
error of 0.2%.
Figure 36. Current Steering DAC Used as a Divider or
Programmable Gain Element
DAC leakage current is also a potential error source in divider
circuits. The leakage current must be counterbalanced by an
opposite current supplied from the op amp through the DAC.
Since only a fraction, D, of the current into the VREF terminal is
routed to the IOUT1 terminal, the output voltage has to change
as follows:
Output Error Voltage Due to DAC Leakage = (Leakage × R)/D
where R is the DAC resistance at the VREF terminal. For a DAC
leakage current of 10 nA, R = 10 k. With a gain (that is, 1/D)
of 16 the error voltage is 1.6 mV.
REFERENCE SELECTION
When selecting a reference for use with the AD5425 current
output DAC, pay attention to the reference’s output voltage
temperature coefficient specification. This parameter not only
affects the full-scale error, but can also affect the linearity (INL
and DNL) performance. The reference temperature coefficient
should be consistent with the system accuracy specifications.
For example, an 8-bit system required to hold its overall
specification to within 1 LSB over the temperature range 0°C to
50°C dictates that the maximum system drift with temperature
should be less than 78 ppm/°C. A 12-bit system with the same
temperature range to overall specification within 2 LSB requires
a maximum drift of 10 ppm/°C. By choosing a precision
reference with a low output temperature coefficient, this error
source can be minimized. Table 7 suggests some of the
references available from Analog Devices that are suitable for
use with this range of current output DACs.
R1
R3
R2
VIN
R1 = R2R3
R2 + R3
GAIN = R2 + R3
R2
NOTES:
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
VOUT
GND
IOUT2
IOUT1
RFB
A1
VREF
VDD
C1
03161-035
GND
IOUT1
RFB
VREF
VDD
NOTE:
1. ADDITIONAL PINS OMITTED FOR CLARITY.
VOUT
VIN
03161-036
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B5K-EY | CONVERTER MOD DC/DC 40V 50W |
| V375C2E50BL3 | CONVERTER MOD DC/DC 2V 50W |
| VI-B4R-EY | CONVERTER MOD DC/DC 7.5V 50W |
| VI-B4M-EY | CONVERTER MOD DC/DC 10V 50W |
| V375C2E50BL2 | CONVERTER MOD DC/DC 2V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5426EB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD5426, 0BIT HIGH BANDWIDTH MULTIPLYING DACS W/ - Bulk |
| EVAL-AD5428EBZ | 制造商:Analog Devices 功能描述:EVAL BD FOR 8-/10-/12-BIT, PARALLEL INPUT, DUAL-CH, CURRENT - Bulk |
| EVAL-AD5429EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD5429EBZ | 制造商:Analog Devices 功能描述:Evaluation Board Dual 8/10/12Bit, High Bandwidth, Multiplying DACs With Serial Interface 制造商:Analog Devices 功能描述:EVAL BD DUAL 8-/10-/12-BIT, HIGH BANDWIDTH, MULTIPLYING DACS - Bulk |
| EVAL-AD5432EB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD5432, 0BIT HIGH BANDWIDTH MULTIPLYING DACS W/ - Bulk |
发布紧急采购，3分钟左右您将得到回复。