参数资料
型号: EVAL-AD7706EBZ
厂商: Analog Devices Inc
文件页数: 8/44页
文件大小: 0K
描述: BOARD EVALUATION FOR AD7706
标准包装: 1
ADC 的数量: 1
位数: 16
采样率(每秒): 500
数据接口: 串行
输入范围: 0 ~ 5.25 V
在以下条件下的电源(标准): 6.5mW @ 500SPS
工作温度: -40°C ~ 85°C
已用 IC / 零件: AD7706
已供物品: 板,CD
相关产品: AD7706BNZ-ND - IC ADC 16BIT 3CHAN 16DIP
AD7706BRUZ-REEL7-ND - IC ADC 16BIT 3CHAN 16TSSOP
AD7706BRZ-REEL7TR-ND - IC ADC 16BIT 3CHAN 16SOIC
AD7706BRUZ-REEL-ND - IC ADC 16BIT 3CHAN 16TSSOP
AD7706BRZ-REEL-ND - IC ADC 16BIT 3CHAN 16SOIC
AD7706BRZ-ND - IC ADC 16BIT 3CH 16-SOIC
AD7706BRUZ-ND - IC ADC 16BIT 3CH 16-TSSOP
AD7706BRU-REEL7-ND - IC ADC 16BIT 3CH 16-TSSOP T/R
AD7706BRU-ND - IC ADC 16BIT 3CH 16-TSSOP
AD7706BR-REEL7-ND - IC ADC 16BIT 3CH 16-SOIC T/R
更多...
AD7705/AD7706
Rev. C | Page 16 of 44
ON-CHIP REGISTERS
The AD7705/AD7706 each contain eight on-chip registers that
can be accessed via the serial port. The first of these is a
communication register that controls the channel selection,
decides whether the next operation is a read or write operation,
and decides which register the next read or write operation
accesses.
All communication to the AD7705/AD7706 must start with a
write operation to the communication register. After a power-
on or reset, the device expects a write to its communication
register. The data written to this register determines whether
the next operation is a read or write operation and to which
register this operation occurs. Therefore, write access to any
register on the part starts with a write operation to the
communication register, followed by a write to the selected
register. Likewise, a read operation from any register on the
part, including the communication register itself and the output
data register, starts with a write operation to the communica-
tion register, followed by a read operation from the selected
register. The communication register also controls the standby
mode and channel selection. The DRDY status is available by
reading from the communication register.
The second register is a setup register that determines
calibration mode, gain setting, bipolar/unipolar operation, and
buffered mode. The third register is labeled the clock register
and contains the filter selection bits and clock control bits. The
fourth register is the data register from which the output data is
accessed. The final registers are the calibration registers, which
store channel calibration data. The registers are discussed in
more detail in the following sections.
COMMUNICATION REGISTER
(RS2, RS1, RS0 = 0, 0, 0)
The communication register is an 8-bit register from which data
can be read or to which data can be written. All communication
to the part must start with a write operation to its communica-
tion register. The data written to the communication register
determines whether the next operation is a read or write
operation and to which register this operation takes place. After
the read or write operation is complete, the interface returns to
its default state, where it expects a write operation to the
communication register. In situations where the interface
sequence is lost, a write operation of a least 32 serial clock
cycles with DIN high returns the ADC to its default state by
resetting the part. Table 10 outlines the bit designations for the
communication register.
Table 9. Communication Register
0/DRDY (0)
RS2 (0)
RS1 (0)
RS0 (0)
R/W (0)
STBY (0)
CH1 (0)
CH0 (0)
Table 10. Communication Register Bit Description
Register
Description
0/DRDY
For a write operation to the communications register, a 0 must be written to this bit. If a 1 is written to this bit, the part does
not clock subsequent bits into the register. It stays at this bit location until a 0 is written. Then, the next seven bits are loaded
into the communication register. For a read operation, this bit provides the status of the DRDY flag, which is the same as the
DRDY output pin.
RS2–RS0
Register Selection Bits. These bits are used to select which of the AD7705/AD7706 registers are being accessed during the
serial interface communication.
R/W
Read/WRITE Select. This bit selects whether the next operation is a read or write operation. A 0 indicates a write cycle for the
next operation to the selected register, and a 1 indicates a read operation from the selected register.
STBY
Standby. Writing 1 to this bit puts the part into standby or power-down mode. In this mode, the part consumes only 10 μA of
power supply current. The part retains its calibration coefficients and control word information when in standby. Writing 0 to
this bit places the parts in normal operating mode.
CH1, CH0
Channel Select. These two bits select a channel for conversion or for access to the calibration coefficients, as outlined in
Table 12. Following a calibration on a channel, three pairs of calibration registers store the calibration coefficients. Table 12
(for the AD7705) and Table 13 (for the AD7706) show which channel combinations have independent calibration coefficients.
With CH1 at Logic 1 and CH0 at Logic 0, the AD7705 looks at the AIN1() input internally shorted to itself, while the AD7706 looks
at the COMMON input internally shorted to itself. This can be used as a test method to evaluate the noise performance of the
parts with no external noise sources. In this mode, the AIN1()/COMMON input should be connected to an external voltage
within the allowable common-mode range for the parts.
相关PDF资料
PDF描述
SDS130R-473M INDUCTOR PWR SHIELDED 47UH SMD
ECM10DKKI CONN EDGECARD 20POS .156 WW
EBC18DRYN-S93 CONN EDGECARD 36POS DIP .100 SLD
VI-B7K-EY CONVERTER MOD DC/DC 40V 50W
RYM06DTKN-S288 CONN EDGECARD 12POS .156 EXTEND
相关代理商/技术参数
参数描述
EVAL-AD7707EB 制造商:Analog Devices 功能描述:EVAL KIT FOR 3V/5 V, 610 V INPUT RANGE, 1 MW 3-CH 16BIT, SIG - Bulk
EVAL-AD7708EB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-AD7708EBZ 功能描述:BOARD EVAL FOR AD7708 RoHS:是 类别:编程器,开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率(每秒):94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源(标准):- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,软件
EVAL-AD7709EB 制造商:Analog Devices 功能描述:EVAL KIT FOR 16BIT- ADC W/ SWITABLE CURRENT SOURCES - Bulk
EVAL-AD7710EB 制造商:AD 制造商全称:Analog Devices 功能描述:Signal Conditioning ADC