参数资料
| 型号： | EVAL-ADE7759EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 12/36页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR ADE7759 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 已用 IC / 零件： | ADE7759 |
| 已供物品： | 板 |
| 相关产品： | ADE7759ARSZRL-ND - IC ENERGY METERING 1PHASE 20SSOP ADE7759ARSZ-ND - IC ENERGY METERING 1PHASE 20SSOP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ADE7759
It is also possible to adjust offset errors on Channel 1 and
CH1OS[5:0]
Channel 2 by writing to the offset correction registers (CH1OS
and CH2OS, respectively). These registers allow channel
offsets in the range ± 24 mV to ± 50 mV (depending on the
gain setting) to be removed. Note that it is not necessary to
perform an offset correction in an energy measurement applica-
1Fh
00h
01,1111b SIGN + 5 BITS
tion if HPF1 Channel 1 is switched on. Figure 6 shows the
effect of offsets on the real power calculation; an offset on
Channel 1 and Channel 2 will contribute a dc component
–50mV
0mV
+50mV
OFFSET
ADJUST
after multiplication. Since this dc component is extracted by
LPF2 to generate the active (real) power information, the
offsets will have contributed an error to the active power
3Fh
11,1111b SIGN + 5 BITS
calculation. This problem is easily avoided by enabling HPF1
in Channel 1. By removing the offset from at least one channel,
no error component is generated at dc by the multiplication.
Error terms at cos( ω t) are removed by LPF2 and by integra-
tion of the active power signal in the active energy register
(AENERGY[39:0])—see Energy Calculation section.
DC COMPONENT (INCLUDING ERROR TERM)
IS EXTRACTED BY THE LPF FOR REAL
POWER CALCULATION
Figure 7. Channel Offset Correction Range (Gain = 1)
di/dt CURRENT SENSOR AND DIGITAL INTEGRATOR
The di/dt sensor detects changes in magnetic field caused by ac
current. Figure 8 shows the principle of a di/dt current sensor.
MAGNETIC FIELD CREATED BY CURRENT
(DIRECTLY PROPORTIONAL TO CURRENT)
V OS
V
2
I OS
I
0
I OS
V OS
V
I
2
+ EMF (ELECTROMOTIVE FORCE)
– INDUCED BY CHANGES IN
MAGNETIC FLUX DENSITY (di/dt)
Figure 8. Principle of a di/dt Current Sensor
Figure 6. Effect of Channel Offsets on the Real
Power Calculation
The contents of the offset correction registers are 6-bit, sign and
magnitude coded. The weighting of the LSB size depends on
the gain setting, i.e., 1, 2, 4, 8, or 16. Table II shows the
correctable offset span for each of the gain settings and the LSB
weight (mV) for the offset correction registers. The maximum
value that can be written to the offset correction registers is ± 31
decimal—see Figure 7.
Table II. Offset Correction Range
The flux density of a magnetic field induced by a current is directly
proportional to the magnitude of the current. The changes in the
magnetic flux density passing through a conductor loop generate
an electromotive force (EMF) between the two ends of the loop.
The EMF is a voltage signal that is proportional to the di/dt of
the current. The voltage output from the di/dt current sensor
is determined by the mutual inductance between the current-
carrying conductor and the di/dt sensor. Figure 9 shows that
the mutual inductance produces a di/dt signal at the output
of the sensor.
Gain
Correctable Span
LSB Size
MUTUAL INDUCTANCE M
1
2
4
8
16
± 50 mV
± 37 mV
± 30 mV
± 26 mV
± 24 mV
1.61 mV/LSB
1.19 mV/LSB
0.97 mV/LSB
0.84 mV/LSB
0.77 mV/LSB
i(t)
+
v=M
–
di(t)
dt
Figure 7 shows the relationship between the offset correction
register contents and the offset (mV) on the analog inputs for a
gain setting of one. To perform an offset adjustment, the analog
inputs should be first connected to AGND, and there should be
no signal on either Channel 1 or Channel 2. A read from
Channel 1 or Channel 2 using the waveform register will give an
indication of the offset in the channel. This offset can be
canceled by writing an equal but opposite offset value to the
relevant offset register. The offset correction can be confirmed
by performing another read. Note that when adjusting the offset of
Channel 1, the digital integrator and the HPF1 should be disabled.
Figure 9. Mutual Inductance Between the di/dt
Sensor and the Current Carrying Conductor
The current signal needs to be recovered from the di/dt signal
before it can be used for active power calculation. An integrator
is therefore necessary to restore the signal to its original form.
The ADE7759 has a built-in digital integrator to recover the
current signal from the di/dt sensor. The digital integrator on
Channel 1 is switched on by default when the ADE7759 is
powered up. Setting the MSB of the CH1OS register to 0 will
turn off the integrator. Figures 10 to 13 show the magnitude
and phase response of the digital integrator.
–12 –
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| EVAL-ADE7762EBZ | BOARD EVALUATION FOR ADE7762 |
| EVAL-ADE7763ZEB | BOARD EVALUATION FOR ADE7763 |
| EVAL-ADE7816EBZ | BOARD EVALUATION FOR ADE7816 |
| EVAL-ADE7878EBZ | BOARD EVAL FOR ADE7878 |
| EVAL-ADE7880EBZ | BOARD EVAL FOR ADE7880 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADE7762EBZ | 功能描述:BOARD EVALUATION FOR ADE7762 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-ADE7763EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD DOCUMENTATION ADE7763 ENERGY METERING IC |
| EVAL-ADE7763ZEB | 功能描述:BOARD EVALUATION FOR ADE7763 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| EVAL-ADE7816EBZ | 功能描述:BOARD EVALUATION FOR ADE7816 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| EVAL-ADE7854EBZ | 制造商:Analog Devices 功能描述:EVALUATION BOARDS - Boxed Product (Development Kits) |
发布紧急采购，3分钟左右您将得到回复。