- 您现在的位置：买卖IC网 > PDF目录97935 > EVB3020A GSM Multiband RF Transceiver PDF资料下载
参数资料
| 型号： | EVB3020A |
| 英文描述： | GSM Multiband RF Transceiver |
| 中文描述： | 手机多频段射频收发器 |
| 文件页数： | 26/44页 |
| 文件大小： | 409K |
| 代理商： | EVB3020A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Advance Data Sheet
W3020 GSM Multiband RF Transceiver
December 1999
32
Lucent Technologies Inc.
Programming Information (continued)
Filter Tune and dc Offset Correction Timing (continued)
dc Offset Calibration
The dc offset calibration operation is controlled by several bits in the CONFIG and TR registers:
n
DS: dc correction skip, in the TR register
n
DP: dc precharge only, in the TR register
n
C5: dc correction disable, in the CONFIG register
n
C7: dc coarse/fine correction, in the CONFIG register
n
DT: dc correction time, in the CONFIG register
When the dc correction disable bit (C5) in the CONFIG register is written high, the dc offset correction circuitry
charges to a default value, corresponding to 0 dc offset, and any request for dc offset calibration is ignored. If dc
correction disable = 0, the dc offset calibration is initiated by writing the MO bits in the TR (or MAIN) register to a
value of 111 while dc correction skip (DS) and dc precharge only (DP) are both low. As in the case of the filter
tune, start of dc offset calibration is held off for about 15
s while the bias circuits and input clock buffer start-up.
If the FTR bit was also written high coincident with entering RX mode, a filter tune is performed first, after which
dc offset calibration begins automatically.
The dc offset calibration runs for a time determined by the dc offset correction time bits DT[0:2] in the CONFIG
register. There are three of these bits, giving the user a choice of eight different correction times.
Upon completion of the dc offset calibration, the 3.25 MHz baseband clock stops and full receive mode is
entered automatically, with the LO1 buffer and LNA (if G0 = 1) being enabled automatically.
If RX mode is entered with dc precharge only (DP = 1) set high, dc offset circuitry runs through a much shorter
calibration routine, after which normal receive mode is entered automatically. The precharge-only operation
functions much the same as the normal calibration operation in that the LO1 buffer and LNA is disabled until
completion of the precharge operation. The 15
s bias start-up time is still incurred.
The receive circuitry conditions during dc calibration are also controlled by two other bits in the CONFIG register:
n
C2: LNA on during dc calibration, when high
n
C3: receive LO1 buffer on during dc, calibration when high
For both the standard dc offset calibration cycle and the dc precharge-only operation, it is possible to perform dc
offset calibration with the LNA and/or LO1 buffer on by setting the C2 and C3 bits in the CONFIG register.
相关PDF资料 |
PDF描述 |
|---|---|
| EVB3020A-IFBD | GSM Multiband RF Transceiver |
| EVB3030A | W3030 3 V Dual-Mode IF Cellular Receiver |
| EVB72001 | EVB72001 EValuation board for TH72001 |
| EVB72002 | EVB72002 EValuation Board for TH72002 |
| EVB72011 | EVB72011 EValuation Board for TH72011 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVB3020A-IFBD | 制造商:AGERE 制造商全称:AGERE 功能描述:GSM Multiband RF Transceiver |
| EVB3030A | 制造商:AGERE 制造商全称:AGERE 功能描述:W3030 3 V Dual-Mode IF Cellular Receiver |
| EVB-3250 | 功能描述:界面开发工具 Evaluation Board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| EVB32-M8L | 制造商:Leviton Manufacturing Co 功能描述: |
| EVB-3300 | 功能描述:界面开发工具 USB3300 Hi-Speed USB Phy Evaluation Board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。