- 您现在的位置：买卖IC网 > PDF目录97935 > EVB3020A GSM Multiband RF Transceiver PDF资料下载
参数资料
| 型号： | EVB3020A |
| 英文描述： | GSM Multiband RF Transceiver |
| 中文描述： | 手机多频段射频收发器 |
| 文件页数： | 27/44页 |
| 文件大小： | 409K |
| 代理商： | EVB3020A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Advance Data Sheet
December 1999
W3020 GSM Multiband RF Transceiver
Lucent Technologies Inc.
33
Programming Example
This programming example shows how the W3020 can be programmed after power-on and how it can be
programmed prior to receive and transmit bursts. The reference register for the W3000 is initialized separately
with the reference divider ratio, as described in the W3000 data sheet.
Table 43. Initialize CONFIG Register (Reset W3020)
To reset all registers to their default state and put the device into a low-power sleep mode, one write to the
CONFIG register is necessary. This will also reset W3000 if it is connected on the same three-wire bus.
Normally, the device will be both reset and configured in the same programming as follows:
CONFIG register: reset device, set dc calibration time to max value (486 s), set phase detector polarity for the
positive slope VCO, use high BW and coarse dc offset tune.
Bit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Bit No.
A0
A1
RS DT0 DT1 DT2 C1
C2
C3
C4
C5
C6
C7 LD2 C8
VO
C9 OLD C10
F1
F2
F3
F4
A2
Setting
1
0
1
0
1
0
1
0
1
0
1
Note: Hex value = 84827d.
Table 44. Initialize TR Register
The reset operation will set the TR register to the following content:
Bit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Bit No.
A0
A1=0
G0
G1
G2
G3
G4
G5
G6
T0
T1
T2
DS
DP
FTR
T3
T4
T5
T6
MO1
MO2
MO3
B
A2
Setting
0
1
Note: Hex value = 800000.
A filter tune request with this TR content, setting FTR = 1 and MO[1:3] = 111, could be done as a second
initialize followed by a third programming that powers the IC in idle mode.
Table 45. Settle PLL to GSM1800 Band for Receive Mode (W3020/W3000)
Main register: switch to W3020 receive settling mode to allow LO2 to settle; band bit B = 1 for GSM1800.
(W3000 is programmed at the same time to settle LO1 to 1572 MHz frequency with N = 7860 to receive at
1842 MHz.)
Bit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Bit No.
A0=0 A1
A2
A3
A4
A5
A6
A7
M1
M2
M3
M4
M5
M6
M7
M8
M9 M10 M11 MO1 MO2 MO3/EN B A1=0
Setting
0
1
0
1
0
1
0
1
0
1
0
1
0
Notes:
Hex value = 687A68.
Italics indicate W3000 bits.
相关PDF资料 |
PDF描述 |
|---|---|
| EVB3020A-IFBD | GSM Multiband RF Transceiver |
| EVB3030A | W3030 3 V Dual-Mode IF Cellular Receiver |
| EVB72001 | EVB72001 EValuation board for TH72001 |
| EVB72002 | EVB72002 EValuation Board for TH72002 |
| EVB72011 | EVB72011 EValuation Board for TH72011 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVB3020A-IFBD | 制造商:AGERE 制造商全称:AGERE 功能描述:GSM Multiband RF Transceiver |
| EVB3030A | 制造商:AGERE 制造商全称:AGERE 功能描述:W3030 3 V Dual-Mode IF Cellular Receiver |
| EVB-3250 | 功能描述:界面开发工具 Evaluation Board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| EVB32-M8L | 制造商:Leviton Manufacturing Co 功能描述: |
| EVB-3300 | 功能描述:界面开发工具 USB3300 Hi-Speed USB Phy Evaluation Board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。