- 您现在的位置：买卖IC网 > PDF目录15802 > FR3-1M (TechTools)EMULATOR FLASH FLEXROM III 1MEG PDF资料下载
参数资料
| 型号： | FR3-1M |
| 厂商： | TechTools |
| 文件页数： | 32/38页 |
| 文件大小： | 0K |
| 描述： | EMULATOR FLASH FLEXROM III 1MEG |
| 标准包装： | 1 |
| 系列： | FlexROM™ III |
| 类型： | 存储器 |
| 适用于相关产品： | 外部 FLASH、EPROM 或 SRAM 设备 |
| 所含物品： | 需要 FR3 FlexROM III 仿真器、缆线（菊花链、LPT、迷你型夹和目标）、软件、有源缆线模块 |
| 其它名称： | FR31M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页
Bad Code
Remember, the one variable that is always changing in this set up is the code itself! If you keep a baseline
code image on hand that is known to work, you could always load that image into the emulator as a sort of
sanity check.
Bad Target Hardware
Try running the target from an EPROM that contains known good code to see if the hardware functions
without the emulator. This is always a good sanity check if things just stopped working and the ‘Bad Code’
suggestions above did not help.
Arbitration Time-outs
Arbitration time-outs are reported when Flex ROM III was unable to complete a memory access within
about 65 us. This can only happen if arbitration has been enabled. If you did NOT intend to do arbitrated
accesses, remove the “/A” parameter from the loader command line or turn on the “RESET during
DOWNLOADS” option in Quickloader. If you truly meant to do arbitrated accesses to the memory space
while the target is using that same space, verify the following:
If you are using READY arbitration, the emulator MUST see target activity to properly arbitrate with it. If
the target is not accessing the memory space emulated by this emulator, it will not see activity and therefore
will not be able to arbitrate. The emulator must see ACTIVITY (both start of accesses and end of
accesses). Also note the /READY line uses an open collector driver and provides a very weak pull-up
resistor. If the target does not provide a pull-up at the connection point, you may need to add a 1K - 10K
resistor between the connection point and your target’s VCC to improve rise times.
If you are using REQUEST/GRANT arbitration, verify that the target arbiter is working, both /RESET and
/GRANT are properly connected and that the target arbiter expects an active LOW /REQUEST and
generates an active LOW /GRANT (if using FEGRANT) or an active HIGH GRANT(if using REGRANT).
Also note that /REQUEST is an open collector driver to allow multiple emulators arbitrate in parallel. If
your target does not provide a pull-up resistor at the attachment point, you may need to add one (around
10K should do).
If you are using CYCLE INTERLEAVING arbitration, verify that you set the arbitration option to READY
mode and left the ready line disconnected. Also verify that the target cycle time is at least 300ns. This is
measured from the END of one cycle (CS, OE or WRITE going INACTIVE) to data stable requirement in
the next cycle.
If you are using Cycle Paralleling, verify that the selected ‘grant’ signal truly indicates that the target will
not expect data from the emulator for at least 300ns. You could verify this with a 2 channel scope. Trigger
one channel on the selected ’grant’ signal. Connect the 2 nd channel to the emulator’s chip select line. If the
two NEVER go active at the same time, or if there is always at least 300ns between the start of the ‘grant’
signal and the start of the emulator chip select, then it should work.
FlexROM III User’s Manual
30
Copyright ? 2001, TechTools
相关PDF资料 |
PDF描述 |
|---|---|
| RP20-2415DFW-HC | CONV DC/DC 20W 9-36VIN +/-15VOUT |
| RP20-2412DFW-HC | CONV DC/DC 20W 9-36VIN +/-12VOUT |
| RL822-3R3K-RC | INDUCTOR FIXED 3.3UH 10% RADIAL |
| RP20-2405DFW-HC | CONV DC/DC 20W 9-36VIN +/-05VOUT |
| ECM06DTMT-S273 | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FR-31SERIES | 制造商:未知厂家 制造商全称:未知厂家 功能描述:surface mount circulator |
| FR31-SERIES | 制造商:未知厂家 制造商全称:未知厂家 功能描述:surface mount circulator |
| FR32 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Single Junction Surface Mount Isolator 800MHz, 900MHz, 1800MHz, 1900MHz, 2100MHz |
| FR-32 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:surface mount isolator |
| FR32-0001 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Single Junction Surface Mount Isolator 800MHz, 900MHz, 1800MHz, 1900MHz, 2100MHz |
发布紧急采购，3分钟左右您将得到回复。