- 您现在的位置：买卖IC网 > PDF目录15802 > FR3-1M (TechTools)EMULATOR FLASH FLEXROM III 1MEG PDF资料下载
参数资料
| 型号： | FR3-1M |
| 厂商： | TechTools |
| 文件页数： | 9/38页 |
| 文件大小： | 0K |
| 描述： | EMULATOR FLASH FLEXROM III 1MEG |
| 标准包装： | 1 |
| 系列： | FlexROM™ III |
| 类型： | 存储器 |
| 适用于相关产品： | 外部 FLASH、EPROM 或 SRAM 设备 |
| 所含物品： | 需要 FR3 FlexROM III 仿真器、缆线（菊花链、LPT、迷你型夹和目标）、软件、有源缆线模块 |
| 其它名称： | FR31M |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
Connect RESET
The RESET line must be connected to guarantee proper target operation. The reset signal is automatically
asserted during each emulator access. This prevents the target from “running stupid” while we change its
code space. The reset signal is released at the completion of the transfer, allowing the target to restart with
the new code image. We also use the reset line to prevent the target from attempting to execute code before
the emulator recognizes that the target has sufficient voltage to run.
FlexROM III provides two reset outputs. RESET is an open emitter, ACTIVE HIGH output. /RESET is an
open collector ACTIVE LOW output. Both signals are pulled to the in-active state via very weak resisters.
Connect the appropriate output to your target’s RESET circuitry.
FlexROM III’s reset signal should be connected to the target’s reset circuitry at the most “upstream” point
available. This is usually an RC combination that senses the target’s power up or a manual reset switch.
Sometimes this circuitry is connected directly to the CPU reset input. In other targets, it will be connected
to the input to a reset chip, power management chip, a watchdog timer chip or a Schmitt trigger gate.
DO NOT CONNECT FlexROM III’s RESET OUTPUT
ACROSS A TOTEM-POLE OR BIPOLAR GATE, OR
DIRECTLY TO GROUND OR 5VOLTS. THIS MAY
RESULT IN DAMAGE TO
FlexROM III OR THE TARGET.
If your target has a reset button, determining where to connect the reset line is easy. Use a DVM, SCOPE
or logic probe to measure the voltage of both sides of the switch. They should be different (one HIGH and
one GROUND). Push and hold the button and take the two measurements again. Both should now be the
same (HIGH or GROUND). Notice that one side of the switch remained the same, the other side changed
states. Connect the reset lead to the side that CHANGED STATES. The level at this point indicates which
POLARITY (RESET or /RESET) we should use. Ground indicates active LOW; use /RESET. HIGH
indicates active high; use RESET.
The next easiest connection point is an RC reset network. If you find a resister and capacitor in series
between power and ground with the common point connected to the CPU or a monitor chip marked
something like reset or clear, you probably found it. Connect the reset line at the RC juncture. If the
resister is connect to ground and the capacitor is connected to power, use the RESET signal. If the resister
is connected to power and the capacitor is connected to ground, use the /RESET signal. In some targets, the
resistor or the capacitor may be missing but these instructions would still apply if you imagine the missing
component is internal to the processor or monitor chip. If you are not sure, ask ‘sparkie’ (a technical term
for the hardware engineer that designed the board).
Call our technical support if you are unsure about which output to use or where to connect to your target.
FlexROM III User’s Manual
7
Copyright ? 2001, TechTools
相关PDF资料 |
PDF描述 |
|---|---|
| RP20-2415DFW-HC | CONV DC/DC 20W 9-36VIN +/-15VOUT |
| RP20-2412DFW-HC | CONV DC/DC 20W 9-36VIN +/-12VOUT |
| RL822-3R3K-RC | INDUCTOR FIXED 3.3UH 10% RADIAL |
| RP20-2405DFW-HC | CONV DC/DC 20W 9-36VIN +/-05VOUT |
| ECM06DTMT-S273 | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FR-31SERIES | 制造商:未知厂家 制造商全称:未知厂家 功能描述:surface mount circulator |
| FR31-SERIES | 制造商:未知厂家 制造商全称:未知厂家 功能描述:surface mount circulator |
| FR32 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Single Junction Surface Mount Isolator 800MHz, 900MHz, 1800MHz, 1900MHz, 2100MHz |
| FR-32 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:surface mount isolator |
| FR32-0001 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Single Junction Surface Mount Isolator 800MHz, 900MHz, 1800MHz, 1900MHz, 2100MHz |
发布紧急采购，3分钟左右您将得到回复。