- 您现在的位置：买卖IC网 > PDF目录1922 > FT2232D-REEL (FTDI, Future Technology Devices International Ltd)IC USB FS DUAL UART/FIFO 48-LQFP PDF资料下载
参数资料
| 型号： | FT2232D-REEL |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 43/61页 |
| 文件大小： | 0K |
| 描述： | IC USB FS DUAL UART/FIFO 48-LQFP |
| 产品培训模块： | USB Introduction |
| 标准包装： | 1 |
| 系列： | USBmadeEZ-FIFO，FT-X，X-Chip |
| 特点： | USB 至 UART 和（或）FIFO、SPI、I2C、JTAG |
| 通道数： | 2，DUART |
| FIFO's： | 384 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 4.35 V ~ 5.25 V |
| 带并行端口： | 是 |
| 带自动流量控制功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP |
| 包装： | 标准包装 |
| 产品目录页面： | 634 (CN2011-ZH PDF) |
| 配用： | 768-1030-ND - MOD USB HS FT2232H EVAL 813-1009-ND - MODULE USB-TO-FPGA TOOL W/MANUAL 813-1001-ND - MODULE USB ADAPTR FOR FT2232D LP 813-1000-ND - MODULE USB ADAPTER FOR FT2232D |
| 其它名称： | 768-1010-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页当前第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页
Copyright 2010 Future Technology Devices International Limited
48
Document No.: FT_000173
FT2232D DUAL USB TO SERIAL UART
/FIFO IC Datasheet
Version 2.05
Clearance No.: FTDI# 127
8.7 Fast Opto-Isolated Serial Interface Mode Signal Descriptions and
Interface Configuration
Fast Opto-Isolated Serial Interface Mode provides a method of communicating with an external device
over USB using 4 wires that can have opto-isolators in their path, thus providing galvanic isolation
between systems. If either channel A or channel B are enabled in fast opto-isolated serial mode then the
pins on channel B are switched to the fast serial interface configuration. The I/O interface for fast serial
mode is always on channel B, even if both channels are being used in this mode. An address bit is used
to determine the source or destination channel of the data. It therefore makes sense to always use at
least channel B or both for fast serial mode, but not A own its own.
When either Channel B or Both Channel A and B are configured in Fast Opto-Isolated Serial Interface
mode following IO signal lines are configured as follows :-
Pin#
Signal
Type
Description
40
FSDI
INPUT
Fast serial data input **Note 30
39
FSCLK
INPUT
Clock input to FT2232D chip to clock data in or out.
The external device has to provide a clock signal or
nothing will change on the interface pins. This gives
the external device full control over the interface. It
is designed to be half duplex so that data is only
transferred in one direction at a time. **Note 30
38
FSDO
OUTPUT
Fast serial data output. Driven low to indicate that
the chip is ready to send data.
37
FSCTS
OUTPUT
Clear To Send control signal output
26
SI/WU
INPUT
The Send Immediate / WakeUp signal combines
two functions on a single pin. If USB is in suspend
mode (PWREN# = 1) and remote wakeup is
enabled in the EEPROM , strobing this pin low will
cause the device to request a resume on the USB
Bus. Normally, this can be used to wake up the
Host PC.
During normal operation (PWREN# = 0), if this pin
is strobed low any data in the device TX buffer will
be sent out over USB on the next Bulk-IN request
from the drivers regardless of the pending packet
size. This can be used to optimise USB transfer
speed for some applications. Tie this pin to VCCIO if
not used.
Table 8.14 Fast Opto-Isolated Serial Interface Mode IO Signal Lines Configuration
**Note 30: Pulled up to VCCIO via internal 200K resistors. These pins can be programmed to gently pull
low during USB suspend ( PWREN# = “1” ) by setting this option in the EEPROM.
Fast Opto-Isolated serial interface mode is enabled in the external EEPROM.
相关PDF资料 |
PDF描述 |
|---|---|
| FT2232HQ-REEL | IC USB HS DUAL UART/FIFO 64-QFN |
| FT232BL-REEL | IC USB FS SERIAL UART 32-LQFP |
| FT232HL-REEL | IC HS USB TO UART/FIFO 48LQFP |
| FT232RL-REEL | IC USB FS SERIAL UART 28-SSOP |
| FT245BL-REEL | IC USB FS PARALLEL FIFO 32-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT2232D-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:DUAL USB TO SERIAL UART/FIFO IC |
| FT2232H | 制造商:FTDI 制造商全称:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART |
| FT2232H MINI MODULE | 功能描述:界面开发工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| FT2232H_10 | 制造商:FTDI 制造商全称:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC |
| FT2232H_12 | 制造商:FTDI 制造商全称:FTDI 功能描述:Dual High Speed USB to Multipurpose UART/FIFO IC |
发布紧急采购，3分钟左右您将得到回复。