- 您现在的位置：买卖IC网 > PDF目录11800 > FT245RQ-REEL (FTDI, Future Technology Devices International Ltd)IC USB TO PARALLEL FIFO 32-QFN PDF资料下载
参数资料
| 型号： | FT245RQ-REEL |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 7/37页 |
| 文件大小： | 0K |
| 描述： | IC USB TO PARALLEL FIFO 32-QFN |
| 产品培训模块： | USB Introduction |
| 标准包装： | 1 |
| 应用： | USB 至 FIFO 控制器 |
| 接口： | USB，FIFO，（同步/异步） |
| 电源电压： | 1.8 V ~ 5.25 V |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 标准包装 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 634 (CN2011-ZH PDF) |
| 配用： | 768-1020-ND - MOD USB PARALLEL FIFO DEV FT245R |
| 其它名称： | 768-1012-6 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
Copyright 2010 Future Technology Devices International Limited
15
Document No.: FT_000052
FT245R USB FIFO IC Datasheet Version 2.12
Clearance No.: FTDI# 39
4 Function Description
The FT245R is a USB to parallel FIFO interface device which simplifies USB to FIFO designs and reduces
external component count by fully integrating an external EEPROM, USB termination resistors and an
integrated clock circuit which requires no external crystal, into the device. It has been designed to
operate efficiently with a USB host controller by using as little as possible of the total USB bandwidth
available.
4.1 Key Features
Functional Integration. Fully integrated EEPROM, USB termination resistors, clock generation, AVCC
filtering, power-on-reset (POR) and LDO regulator.
Asynchronous Bit Bang Mode. In asynchronous bit-bang mode, the eight FIFO lines can be switched
from the regular interface mode to an 8-bit general purpose I/O port. Data packets can be sent to the
device and they will be sequentially sent to the interface at a rate controlled by an internal timer
(equivalent to the baud rate pre-scaler. This option will be described more fully in a separate application
note available from FTDI website (www.ftdichip.com).
Synchronous Bit Bang Mode. The FT245R supports synchronous bit bang mode. This mode differs from
asynchronous bit bang mode in that the interface pins are only read when the device is written to. This
makes it easier for the controlling program to measure the response to an output stimulus as the data
returned is synchronous to the output data. An application note, AN232R-01, available from FTDI website
(www.ftdichip.com) describes this feature.
FTDIChip-ID. The FT245R also includes the new FTDIChip-ID security dongle feature. This
FTDIChip-ID feature allows a unique number to be burnt into each device during manufacture. This
number cannot be reprogrammed. This number is only readable over USB and forms a basis of a security
dongle which can be used to protect any customer application software being copied. This allows the
possibility of using the FT245R in a dongle for software licensing. Further to this, a renewable license
scheme can be implemented based on the FTDIChip-ID number when encrypted with other information.
This encrypted number can be stored in the user area of the FT245R internal EEPROM, and can be
decrypted, then compared with the protected FTDIChip-ID to verify that a license is valid. Web based
applications can be used to maintain product licensing this way. An application note, AN232R-02,
available from FTDI website (www.ftdichip.com) describes this feature.
High Output Drive Option. The parallel FIFO interface and the four FIFO handshake pins can be made
to drive out at three times the standard signal drive level thus allowing multiple devices to be driven, or
devices that require a greater signal drive strength to be interfaced to the FT245R. This option is
configured in the internal EEPROM.
Programmable FIFO RX Buffer Timeout. The FIFO RX buffer timeout is used to flush remaining data
from the receive buffer. This timeout defaults to 16ms, but is programmable over USB in 1ms increments
from 2ms to 255ms, thus allowing the device to be optimised for protocols that require fast response
times from short data packets.
Wake Up Function. If USB is in suspend mode, and remote wake up has been enabled in the internal
EEPROM (it is enabled by default), the RXF# pin becomes an input. Strobing this pin low for a minimum
of 20ms will cause the FT245R to request a resume from suspend on the USB bus. Normally this can be
used to wake up the host PC from suspend.
The FT245R is capable of operating at a voltage supply between +3.3V and +5V with a nominal
operational mode current of 15mA and a nominal USB suspend mode current of 70A. This allows greater
margin for peripheral designs to meet the USB suspend mode current limit of 2.5mA. An integrated level
converter within the FIFO interface allows the FT245R to interface to FIFO logic running at +1.8V, 2.5V,
+3.3V or +5V.
相关PDF资料 |
PDF描述 |
|---|---|
| V48A12E500BG2 | CONVERTER MOD DC/DC 12V 500W |
| V48A12E500BF3 | CONVERTER MOD DC/DC 12V 500W |
| V48A12E500BF2 | CONVERTER MOD DC/DC 12V 500W |
| V48A12E500BF | CONVERTER MOD DC/DC 12V 500W |
| V48A12E500BL2 | CONVERTER MOD DC/DC 12V 500W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT245RQ-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:Single Chip USB Tray |
| FT24B3 031175 | 制造商:Comair Rotron 功能描述:FAN 120X120X25MM 24VDC |
| FT24B3-E2 | 制造商:Comair Rotron 功能描述:FAN FLIGHT II 120X120X25MM 24V |
| FT24B3-E2 | 制造商:Comair Rotron 功能描述:FAN FLIGHT II 120X120X25 24V |
| FT24C02A | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Two-Wire Serial EEPROM |
发布紧急采购，3分钟左右您将得到回复。