- 您现在的位置：买卖IC网 > PDF目录223865 > GS81302QT07E-333 (GSI TECHNOLOGY) 16M X 8 QDR SRAM, 0.45 ns, PBGA165 PDF资料下载
参数资料
| 型号： | GS81302QT07E-333 |
| 厂商： | GSI TECHNOLOGY |
| 元件分类： | SRAM |
| 英文描述： | 16M X 8 QDR SRAM, 0.45 ns, PBGA165 |
| 封装： | 15 X 17 MM, 1 MM PITCH, FPBGA-165 |
| 文件页数： | 17/30页 |
| 文件大小： | 914K |
| 代理商： | GS81302QT07E-333 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
GS81302QT07/10/19/37E-333/300/250/200
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Rev: 1.00 5/2011
24/30
2011, GSI Technology
loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and
I/O buffers into the Boundary Scan Register. Boundary Scan Register locations are not associated with an input or I/O pin, and
are loaded with the default state identified in the Boundary Scan Chain table at the end of this section of the datasheet. Because
the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents
while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will
not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the
TAPs input data capture set-up plus hold time (tTS plus tTH). The RAMs clock inputs need not be paused for any other TAP
operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to Shift-DR state then
places the boundary scan register between the TDI and TDO pins.
EXTEST
EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with
all logic 0s. The EXTEST command does not block or override the RAM’s input pins; therefore, the RAM’s internal state is
still determined by its input pins.
Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command.
Then the EXTEST command is used to output the Boundary Scan Register’s contents, in parallel, on the RAM’s data output
drivers on the falling edge of TCK when the controller is in the Update-IR state.
Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruc-
tion is selected, the sate of all the RAM’s input and I/O pins, as well as the default values at Scan Register locations not asso-
ciated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR
state, the RAM’s output pins drive out the value of the Boundary Scan Register location with which each output pin is associ-
ated.
IDCODE
The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and
places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction
loaded in at power up and any time the controller is placed in the Test-Logic-Reset state.
SAMPLE-Z
If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (high-
Z) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR
state.
JTAG TAP Instruction Set Summary
Instruction
Code
Description
Notes
EXTEST
000
Places the Boundary Scan Register between TDI and TDO.
1
IDCODE
001
Preloads ID Register and places it between TDI and TDO.
1, 2
SAMPLE-Z
010
Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO.
Forces all RAM output drivers to High-Z.
1
GSI
011
GSI private instruction.
1
SAMPLE/PRELOAD
100
Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO.
1
GSI
101
GSI private instruction.
1
GSI
110
GSI private instruction.
1
BYPASS
111
Places Bypass Register between TDI and TDO.
1
Notes:
1. Instruction codes expressed in binary, MSB on left, LSB on right.
2. Default instruction automatically loaded at power-up and in test-logic-reset state.
相关PDF资料 |
PDF描述 |
|---|---|
| GS81302TT07E-333IT | 16M X 8 DDR SRAM, 0.45 ns, PBGA165 |
| GS81302TT07GE-333I | 16M X 8 DDR SRAM, 0.45 ns, PBGA165 |
| GS816036AGT-250I | 512K X 36 CACHE SRAM, 5.5 ns, PQFP100 |
| GS8160E36GT-250 | 512K X 36 CACHE SRAM, 5.5 ns, PQFP100 |
| GS816118AGT-200IT | 1M X 18 CACHE SRAM, 6.5 ns, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| GS81302S18E-167 | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 1.8V 144MBIT 8MX18 0.5NS 165FPBGA - Trays |
| GS81302S18E-167I | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 1.8V 144MBIT 8MX18 0.5NS 165FPBGA - Trays |
| GS81302S18E-200 | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 1.8V 144MBIT 8MX18 0.45NS 165FPBGA - Trays |
| GS81302S18E-200I | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 1.8V 144MBIT 8MX18 0.45NS 165FPBGA - Trays |
| GS81302S18E-250 | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 1.8V 144MBIT 8MX18 0.45NS 165FPBGA - Trays |
发布紧急采购，3分钟左右您将得到回复。