参数资料
| 型号： | HI5805BIB |
| 厂商： | Intersil |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12-BIT 5MSPS 28-SOIC |
| 标准包装： | 26 |
| 位数： | 12 |
| 采样率（每秒）： | 5M |
| 数据接口： | 并联 |
| 转换器数目： | 3 |
| 功率耗散（最大）： | 350mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 输入数目和类型： | 2 个单端，单极；1 个差分，双极 |
9
Analog Input, Differential Connection
The analog input to the HI5805 can be configured in various
ways depending on the signal source and the required level
of performance. A fully differential connection (Figure 15) will
give the best performance for the converter.
Since the HI5805 is powered off a single +5V supply, the
analog input must be biased so it lies within the analog input
common mode voltage range of 1.0V to 4.0V. The
performance of the ADC does not change significantly with
the value of the analog input common mode voltage.
A 2.3V DC bias voltage source, VDC, half way between the
top and bottom internal reference voltages, is made
available to the user to help simplify circuit design when
using a differential input. This low output impedance voltage
source is not designed to be a reference but makes an
excellent bias source and stays within the analog input
common mode voltage range over temperature.
The difference between the converter’s two internal voltage
references is 2V. For the AC coupled differential input,
(Figure 15), if VIN is a 2VP-P sinewave with -VIN being 180
degrees out of phase with VIN, then VIN+ is a 2VP-P
sinewave riding on a DC bias voltage equal to VDC and
VIN- is a 2VP-P sinewave riding on a DC bias voltage equal
to VDC. Consequently, the converter will be at positive full
scale, all 1s digital data output code, when the VIN+ input is
at VDC +1V and the VIN- input is at VDC -1V (VIN+-VIN- =
2V). Conversely, the ADC will be at negative full scale, all
0s digital data output code, when the VIN+ input is equal to
VDC- 1V and VIN- is at VDC+1V (VIN+-VIN- = -2V). From
this, the converter is seen to have a peak-to-peak
differential analog input voltage range of
±2V.
The analog input can be DC coupled (Figure 16) as long as
the inputs are within the analog input common mode voltage
range (1.0V
≤ VDC ≤ 4.0V).
The resistors, R, in Figure 16 are not absolutely necessary
but may be used as load setting resistors. A capacitor, C,
connected from VIN+ to VIN- will help filter any high
frequency noise on the inputs, also improving performance.
Values around 20pF are sufficient and can be used on AC
coupled inputs as well. Note, however, that the value of
capacitor C chosen must take into account the highest
frequency component of the analog input signal.
Analog Input, Single-Ended Connection
The configuration shown in Figure 17 may be used with a
single ended AC coupled input. Sufficient headroom must be
provided such that the input voltage never goes above +5V
or below AGND.
TABLE 1.
CODE CENTER
DESCRIPTION
DIFFERENTIAL
INPUT VOLTAGE
(USING INTERNAL
REFERENCE)
OFFSET BINARY OUTPUT CODE
MSB
LSB
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
+Full Scale (+FS) - 1/4 LSB
+1.99976V
1
+FS
- 11/4 LSB
1.99878V
1
0
+ 3/4 LSB
732.4
V
1
0
- 1/4 LSB
-244.1
V
0
1
-FS + 13/4 LSB
-1.99829V
0
1
-Full Scale (-FS) + 3/4 LSB
-1.99927V
0
The voltages listed above represent the ideal center of each offset binary output code shown.
VIN+
VDC
VIN-
HI5805
VIN
-VIN
FIGURE 15. AC COUPLED DIFFERENTIAL INPUT
VIN+
VDC
VIN-
HI5805
VIN
-VIN
R
C
VDC
FIGURE 16. DC COUPLED DIFFERENTIAL INPUT
HI5805
相关PDF资料 |
PDF描述 |
|---|---|
| HI5812JIBZ-T | ADC 12BIT SAMPL TRK&HOLD 24-SOIC |
| HI5828IN | DAC DUAL 12BIT 130MHZ 48-LQFP |
| HI5860IBZ | CONV D/A 12-BIT 130MSPS 28-SOIC |
| HI5960IAZ | CONV D/A 14BIT 130MSPS 28-TSSOP |
| HI7188IN | CONV A/D 16BIT 8:1 MUX 44-MQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HI5805BIBZ | 功能描述:模数转换器 - ADC 28 INDTEMP A/D 12BIT 5MSPS 0 5LSB V-REF RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| HI5805EVAL1 | 功能描述:数据转换 IC 开发工具 HI5805 EVAL PL ATFORM RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| HI5806IB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI5808 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 9MSPS A/D Converter |
| HI5808_01 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 9MSPS A/D Converter |
发布紧急采购，3分钟左右您将得到回复。