- 您现在的位置：买卖IC网 > PDF目录9968 > IDT82V2088BB (IDT, Integrated Device Technology Inc)IC LIU T1/J1/E1 8CH 208-BGA PDF资料下载
参数资料
| 型号： | IDT82V2088BB |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 5/78页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/J1/E1 8CH 208-BGA |
| 标准包装： | 10 |
| 类型： | 线路接口装置（LIU） |
| 规程： | E1 |
| 电源电压： | 3.13 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 208-BGA |
| 供应商设备封装： | 208-PBGA（17x17） |
| 包装： | 托盘 |
| 其它名称： | 82V2088BB |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页
13
INDUSTRIAL
TEMPERATURE RANGES
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
DS/RD
Input
47
N3
DS: Data Strobe
In parallel Motorola microcontroller interface mode, signal on this pin is the data strobe of the parallel
interface. During a write operation (R/W =0), data on D[7:0] is sampled into the device. During a read
operation (R/W =1), data is output to D[7:0] from the device.
RD: Read Operation
In parallel Intel microcontroller interface mode, this pin is asserted low by the microcontroller to initiate
a read cycle. Data is output to D[7:0] from the device during a read operation.
SDI/R/W/WR
Input
48
P1
SDI: Serial Data Input
In serial microcontroller interface mode, data is input on this pin. Input data is sampled on the rising
edges of SCLK.
R/W: Read/Write Select
In parallel Motorola microcontroller interface mode, this pin is low for write operation and high for read
operation.
WR: Write Operation
In parallel Intel microcontroller interface mode, this pin is asserted low by the microcontroller to initiate
a write cycle. Data on D[7:0] is sampled into the device during a write operation.
SDO
Output
49
P2
SDO: Serial Data Output
In serial microcontroller interface mode, signal on this pin is the output data of the serial interface. Con-
figuration and status data on pin SDO is clocked out of the device on the active edge of SCLK.
INT
Output
50
R1
INT: Interrupt Request
This pin outputs the general interrupt request for all interrupt sources. If INTM_GLB bit (GCF0, 40H)
is set to ‘1’, all interrupt sources will be masked. And these interrupt sources also can be masked indi-
vidually via registers (INTM0, 11H) and (INTM1, 12H). Interrupt status is reported via byte INT_CH
(INTCH, 80H), registers (INTS0, 16H) and (INTS1, 17H).
Output characteristics of this pin can be defined to be push-pull (active high or low) or be open-drain
(active low) by bits INT_PIN[1:0] (GCF0, 40H).
D7
D6
D5
D4
D3
D2
D1
D0
I / O
24
25
26
27
28
29
30
31
H3
H2
J1
J2
J3
J4
K3
K2
Dn: Data Bus 7~0
These pins function as a bi-directional data bus of the microcontroller interface.
A7
A6
A5
A4
A3
A2
A1
A0
Input
37
38
39
40
41
42
43
44
L1
L2
L3
L4
M4
M3
M2
M1
An: Address Bus 7~0
These pins function as an address bus of the microcontroller interface.
RST
Input
51
P3
RST: Hardware Reset
The chip is reset if a low signal is applied on this pin for more than 100ns. All the drivers output are in
high impedance state, all the internal flip-flops are reset and all the registers are initialized to their
default values.
THZ
Input
10
E4
THZ: Transmit Driver Enable
This pin enables or disables all transmitter drivers on a global basis. A low level on this pin enables the
drivers while a high level turns all drivers into high impedance state. Note that functionality of internal
circuits is not affected by signal on this pin.
REF
Input
59
T1
REF: Reference Resistor
An external resistor (3 K
, 1%) is used to connect this pin to ground to provide a standard reference
current for internal circuit.
Table-1 Pin Description (Continued)
Name
Type
Pin No.
Description
PQFP208
PBGA208
相关PDF资料 |
PDF描述 |
|---|---|
| IDT72V263L7-5PF | IC FIFO 8192X18 7-5NS 80QFP |
| V48B15M250BG2 | CONVERTER MOD DC/DC 15V 250W |
| IDT82V2088BBG | IC LINE INTERFACE UNIT 208-PBGA |
| V48B15M250BF3 | CONVERTER MOD DC/DC 15V 250W |
| IDT72V263L10PFI | IC FIFO 8192X18 10NS 80QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT82V2088BBG | 功能描述:IC LINE INTERFACE UNIT 208-PBGA RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| IDT82V2088DR | 功能描述:IC LIU T1/J1/E1 8CH 208-TQFP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| IDT82V2088DRG | 功能描述:IC LIU T1/J1/E1 8CH 208-TQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| IDT82V2108 | 制造商:IDT 制造商全称:Integrated Device Technology 功能描述:T1 / E1 / J1 OCTAL FRAMER |
| IDT82V2108BB | 功能描述:IC FRAMER T1/J1/E1 8CH 144-BGA RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
发布紧急采购，3分钟左右您将得到回复。