参数资料
型号: IR3510MPBF
厂商: International Rectifier
文件页数: 11/36页
文件大小: 0K
描述: IC XPHASE CONTROL 32-MLPQ
标准包装: 100
系列: XPhase™
应用: 处理器
安装类型: 表面贴装
封装/外壳: 32-VFQFN 裸露焊盘
供应商设备封装: 32-MLPQ(5x5)
包装: 剪切带 (CT)
IR3510
“VFB” (PIN#15): Voltage feedback input. It is internally connected to the inverting input of the voltage error
amplifier.
“IREF” (PIN#16): Voltage error amplifier output. It is also the current reference input to the current error amplifier.
It is clamped by the “OCSET” voltage when it is running in constant current limit mode.
“IGAIN” (PIN#17): Inverting input to the current report amplifier. Connect a resistor network between this pin and
the “IO” pin to program the current report amplifier gain.
“IO” (PIN#18): Current report amplifier output representing the output load current. In order to measure negative
output current in a paralleling system, a fixed 200mv input offset voltage is added to the current report amplifier. At
no load, it reports this offset voltage, which is amplified by the current report gain.
“IFB” (PIN#19): Current feedback input. It is internally connected to the inverting input of the current error
amplifier. The output of “IO” pin is connected to this pin through a resistor.
“EAOUT” (PIN#20): Current error amplifier output. Connect it to the “EA” pin of the phase IC to control the PWM
duty cycle.
“IIN” (PIN#21): Current sense input from the phase IC. It has an offset voltage of “VREF” voltage. Connect it to the
“ISHARE” pin of the phase IC.
“RMPOUT” (PIN#22): Oscillator triangle waveform output. Connect it to the “RMPIN” pin of the phase IC to set the
switching frequency and phase timing. The frequency of this ramp signal is programmed by the resistor connected
to the “ROSC” pin.
“VREF” (PIN#23): Buffered output of “VSET” voltage. Connect it to the “DACIN” pin of the
phase IC to set the
“IIN” offset voltage and the PWM ramp floor voltage.
“ROSC” (PIN#24): Connect an external resistor to program the switching frequency. The lower the resistor value,
the higher the switching frequency. The voltage on this pin can be used as a voltage reference with 1% tolerance.
It is 1.230V typical with Rosc = 42K.
“OR-” (PIN#25): Oring comparator inverting input. Connect it to the DRAIN side of the Oring FET through a
programming resistor. A constant current source flowing out of this pin goes through that programming resistor to
set the reverse current cut-off threshold.
“OR+” (PIN#26): Oring comparator non-inverting input. Connect it to the SOURCE side of the Oring FET.
“GATE_O” (PIN#27): Oring FET gate driver output. It is driven by the internal charge-pump with 10uA charging
and 2A discharging currents. It also has internal 3k resistor pulled-up to VIN to speed up the turn-on of Oring FET.
“LGND” (PIN#28): Local GND for Internal circuit and IC substrate connection.
“GATE_I” (PIN#29): Input FET driver output. It is driven by the internal charge-pump with 20uA charging and 2A
discharging currents.
Page 11 of 36
IR Confidential
May 18, 2009
相关PDF资料
PDF描述
IR3513ZMTRPBF IC CTRL XPHASE3 POL 32-MLPQ
IR3514MTRPBF IC XPHASE3 CONTROL HYBRD 40-MLPQ
IR3521MTRPBF IC CTRL XPHASE3 SVID 32-MLPQ
IR3522MTRPBF IC CTRL XPHASE3 DDR/VVT 32-MLPQ
IR3523MTRPBF IC XPHASE3 CTLR VR11.1 40-MLPQ
相关代理商/技术参数
参数描述
IR3510MTRPBF 功能描述:热插拔功率分布 HOT-SWAP N+1 XPHASE CTRL IC RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
IR3513MTRPBF 功能描述:开关变换器、稳压器与控制器 2 CH OR 2 PHASE SYNC PWM CNTRLR RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
IR3513XMTRPBF 功能描述:功率驱动器IC RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
IR3513Z 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM POL CONTROL IC
IR3513ZMPBF 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM POL CONTROL IC