参数资料
| 型号： | IR3510MPBF |
| 厂商： | International Rectifier |
| 文件页数： | 34/36页 |
| 文件大小： | 0K |
| 描述： | IC XPHASE CONTROL 32-MLPQ |
| 标准包装： | 100 |
| 系列： | XPhase™ |
| 应用： | 处理器 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-MLPQ（5x5） |
| 包装： | 剪切带 (CT) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页
IR3510
SOLDER RESIST
? The solder resist should be pulled away from the metal lead lands by a minimum of 0.06mm. The solder resist
mis-alignment is a maximum of 0.05mm and it is recommended that the lead lands are all Non Solder Mask
Defined (NSMD). Therefore pulling the S/R 0.06mm will always ensure NSMD pads.
? The minimum solder resist width is 0.13mm.
? At the inside corner of the solder resist where the lead land groups meet, it is recommended to provide a fillet so a
solder resist width of ≥ 0.17mm remains.
? The land pad should be Solder Mask Defined (SMD), with a minimum overlap of the solder resist onto the copper
of 0.06mm to accommodate solder resist mis-alignment. In 0.5mm pitch cases it is allowable to have the solder
resist opening for the land pad to be smaller than the part pad.
? Ensure that the solder resist in-between the lead lands and the pad land is ≥ 0.15mm due to the high aspect ratio of
the solder resist strip separating the lead lands from the pad land.
? The four vias in the land pad should be tented or plugged from bottom board side with solder resist.
Page 34 of 36
IR Confidential
May 18, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| IR3513ZMTRPBF | IC CTRL XPHASE3 POL 32-MLPQ |
| IR3514MTRPBF | IC XPHASE3 CONTROL HYBRD 40-MLPQ |
| IR3521MTRPBF | IC CTRL XPHASE3 SVID 32-MLPQ |
| IR3522MTRPBF | IC CTRL XPHASE3 DDR/VVT 32-MLPQ |
| IR3523MTRPBF | IC XPHASE3 CTLR VR11.1 40-MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IR3510MTRPBF | 功能描述:热插拔功率分布 HOT-SWAP N+1 XPHASE CTRL IC RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| IR3513MTRPBF | 功能描述:开关变换器、稳压器与控制器 2 CH OR 2 PHASE SYNC PWM CNTRLR RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| IR3513XMTRPBF | 功能描述:功率驱动器IC RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| IR3513Z | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM POL CONTROL IC |
| IR3513ZMPBF | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM POL CONTROL IC |
发布紧急采购，3分钟左右您将得到回复。