参数资料
| 型号： | IR3510MPBF |
| 厂商： | International Rectifier |
| 文件页数： | 15/36页 |
| 文件大小： | 0K |
| 描述： | IC XPHASE CONTROL 32-MLPQ |
| 标准包装： | 100 |
| 系列： | XPhase™ |
| 应用： | 处理器 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-MLPQ（5x5） |
| 包装： | 剪切带 (CT) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
IR3510
PWM Operation
The PWM comparator is located in the Phase IC. Upon receiving a clock pulse, the PWM latch is set, the
PWMRMP voltage begins to increase, the low side driver is turned off, and the high side driver is then turned on.
When the PWMRMP voltage exceeds the EAOUT voltage the PWM latch is reset. This turns off the high side
driver, turns on the low side driver, and activates the Ramp Discharge Clamp. The clamp quickly discharges the
PWMRMP capacitor to the VDAC voltage of the Control IC until the next clock pulse.
The PWM latch is reset dominant allowing all phases to go to zero duty cycle within a few tens of nanoseconds in
response to a load step decrease. Phases can overlap and go to 100% duty cycle in response to a load step
increase with turn-on gated by the clock pulses. An Error Amp output voltage greater than the common mode input
range of the PWM comparator results in 100% duty cycle regardless of the voltage of the PWM ramp. This
arrangement guarantees the Error Amp is always in control and can demand 0 to 100% duty cycle as required. It
also favors response to a load step decrease which is appropriate given the low output to input voltage ratio of
most systems. The inductor current will increase much more rapidly than decrease in response to load transients.
This control method is designed to provide “single cycle transient response” where the inductor current changes in
response to load transients within a single switching cycle maximizing the effectiveness of the power train and
minimizing the output capacitor requirements. An additional advantage is that differences in ground or input
voltage at the phases have no effect on operation since the PWM ramps are referenced to VREF.
Body Braking
TM
In a conventional synchronous buck converter, the minimum time required to reduce the current in the inductor in
response to a load step decrease is;
T SLEW = [L x (I MAX ? I MIN )] / Vout
The slew rate of the inductor current can be significantly increased by turning off the synchronous rectifier in
response to a load step decrease. The switch node voltage is then forced to decrease until conduction of the
synchronous rectifier’s body diode occurs. This increases the voltage across the inductor from Vout to Vout +
V BODY DIODE . The minimum time required to reduce the current in the inductor in response to a load transient
decrease is now;
T SLEW = [L x (I MAX ? I MIN )] / (Vout + V BODY DIODE )
Since the voltage drop in the body diode is often higher than output voltage, the inductor current slew rate can be
increased by 2X or more. This patent pending technique is referred to as “body braking” and is accomplished
through the “0% Duty Cycle Comparator” located in the Phase IC. If the Error Amp’s output voltage drops below
91% of the VDAC voltage this comparator turns off the low side gate driver.
PHASE IC
CLOCK
PULSE
EAIN
PWMRMP
VDAC
Body-Braking
Threshold
GATEH
GATEL
STEADY-STATE
OPERATION
DUTY CYCLE INCREASE
DUE TO LOAD
INCREASE
DUTY CYCLE DECREASE
DUE TO VIN INCREASE
(FEED-FORWARD)
DUTY CYCLE DECREASE DUE TO LOAD
DECREASE (BODY BRAKING) OR FAULT
(VCC UV, VCCVID UV, OCP, VID=11111X)
STEADY-STATE
OPERATION
Figure 3 – PWM Operating Waveforms
Page 15 of 36
IR Confidential
May 18, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| IR3513ZMTRPBF | IC CTRL XPHASE3 POL 32-MLPQ |
| IR3514MTRPBF | IC XPHASE3 CONTROL HYBRD 40-MLPQ |
| IR3521MTRPBF | IC CTRL XPHASE3 SVID 32-MLPQ |
| IR3522MTRPBF | IC CTRL XPHASE3 DDR/VVT 32-MLPQ |
| IR3523MTRPBF | IC XPHASE3 CTLR VR11.1 40-MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IR3510MTRPBF | 功能描述:热插拔功率分布 HOT-SWAP N+1 XPHASE CTRL IC RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| IR3513MTRPBF | 功能描述:开关变换器、稳压器与控制器 2 CH OR 2 PHASE SYNC PWM CNTRLR RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| IR3513XMTRPBF | 功能描述:功率驱动器IC RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| IR3513Z | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM POL CONTROL IC |
| IR3513ZMPBF | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM POL CONTROL IC |
发布紧急采购，3分钟左右您将得到回复。