参数资料
| 型号： | ISL35822LPIK |
| 厂商： | Intersil |
| 文件页数： | 8/75页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK/DATA RECOVERY 192EBGA-B |
| 标准包装： | 90 |
| 类型： | 时钟和数据恢复（CDR），多路复用器 |
| PLL： | 无 |
| 输入： | CML |
| 输出： | CML，CMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 8:8 |
| 差分 - 输入:输出： | 是/是 |
| 频率 - 最大： | 1.59Gbps |
| 电源电压： | 1.3 V ~ 1.41 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 192-EBGA |
| 供应商设备封装： | 192-EBGA-B（17x17） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
16
I2C Space Interface
In addition to the standard MDIO registers discussed above,
the ISL35822 implements the register addresses specified in
the XENPAK MSA specification for the NVR, DOM and LASI
blocks. The built-in I2C controller can be configured to load
these registers with the MSA-specified data on start-up or
reset or on demand from an I2C EEPROM (frequently
included as part of a DOM circuit) and/or one or four DOM
circuits (see below). Optionally, a portion of the NVR space
may be used to autoload the various ISL35822 control
registers at start-up or reset. These operations are
discussed in more detail below.
NVR Registers & EEPROM
If the XP_ENA pin is asserted enabled (high), at the end of
hardware RESET or power-up the ISL35822 will attempt to
load the NVR area by initiating a NVR-block read through
the 1.32768 (1.8000’h) control register (Table 15). See
Figure 18. The same will occur if the appropriate command
value is written into this register. The I2C interface will
attempt to read the A0.00:FF’h I2C space into the
1.8007:8106’h MDIO register space. The Command Status
bits in the 1.32768 (1.8000’h) Control register will reflect the
status of this operation. Failure may occur if the expected
ACK is not received from any address after the number of
attempts set in control register 1.32273 (1.8005’h), default
timing sequence of this Block Read operation is shown in
Figure 20. The host can check the checksums against the
values at 1.807D, and optionally 1.80AD and 1.8106, and
take appropriate action. As soon as the XENPAK MDIO
space is loaded, the STA MDIO device may interrogate it.
Note that the ISL35822 merely stores the values read from
the EEPROM or other device at A0.00-FF’h, and, with a few
exceptions, does not interpret them in any way. The
exceptions are listed explicitly in Table 22, together with the
other uninterpreted groups, and are:
The Package OUI at 1.32818:32821 (1.8032:5’h), which
will be mirrored in the IEEE-defined 1.14:15 (1.E:F’h)
space, as required by section 10.8.2 of the XENPAK spec;
the allowable values here are specified by the XENPAK,
XPAK and X2 specifications;
The DOM Capability byte at 1.32890 (1.807A), see the
DOM Registers section, page 16;
The Auto-configure size and pointer bytes at
1.33028:9(1.8104:5); (see Auto-Configuring Control
Registers, page 16).
If the Auto-configure operation is enabled, the block of
bytes so specified will be written into the ISL35822 control
registers, (see Auto-Configuring Control Registers on
Other registers may be interpreted in future versions of the
ISL35822.
Auto-Configuring Control Registers
If the XP_ENA pin is asserted, and the I2C controller can
successfully read the I2C NVR space into the MDIO NVR
space, the ISL35822 will examine the Auto-configure Pointer
value at 1.33029 (1.8105’h). If this is neither 00’h or FF’h,
the ISL35822 will use that value (S below) as an offset
pointer into the A0.00:FF’h I2C space already copied into the
MDIO NVR space, and the number of bytes given in the
Auto-configure Size register 1.33028 (1.8104) value (N
below) to load N bytes from the NVR data starting from
location S into the various ISL35822 configuration control
registers. The loading sequence and the correspondence
between the NVR block and the control registers is listed in
Table 92. The auto-configure engine will behave benignly if
the S and N values are misconfigured, so that if S + N
≥ 252
(for example), the auto-configure block will stop at an S + N
value of 252, and not use S, N , or the Checksum value to
load a configuration control register. (Hence the exclusion of
FF’h as a value for S is no limitation). Similarly, values of N >
40 will be ignored.
Note that in a XENPAK/XPAK/X2 module, the value of S should
not be between 00’h and 76’h, since this would start the loading
from within the MSA-defined region. (Hence the exclusion of
00’h as a value for S is normally no limitation). If the value of S
lies between 77’h and A6’h, that portion of the auto-configure
data within that band can be overwritten as part of the
Customer Writable area defined by the MSA specifications; if
this is undesirable, that range of values should also be
excluded. On the other hand, this could be used to allow some
customization for specific end-user configuration values. If the
block overlaps the boundary between the ‘Customer Writable’
and ‘Vendor Specific’ areas, the first part would be customer-
writable, and the second part not. The order of the configuration
registers has been arranged to place those most likely to be
useful in such a customer-configuration environment at the
beginning of the block. The ‘Customer Area Checksum’ would
be part of the auto-configure block, and some other byte in the
‘Customer Writeable Area’ would need to be adjusted to make
the Checksum and the desired configuration value coincide.
The Command Status bits in the NVR Command register
(Table 15) at 1.32768.3:2 (1.8000’h.3:2) will reflect the success
of both the NVR and (if called for) the auto-configure loading
operations.
DOM Registers
If the NVR load operation succeeds, the (newly read-in)
XENPAK register at 1.32890 (1.807A’h) is examined, and if the
will attempt to read the DOM values from the I2C device
address space specified in the same register (bits 2:0),
details. A full block of data will be read from this space (normally
A2.00:FF’h) into the 1.40960:41215 (1.A000: A0FF’h) MDIO
The DOM control register is implemented in the ISL35822 at
ISL35822
相关PDF资料 |
PDF描述 |
|---|---|
| ISL41334IRZ-T7A | IC TXRX RS232/485 DL 2PRT 40QFN |
| ISL43485IB-T | IC TXRX 1TX/1RX 3V RS-485 8-SOIC |
| ISL51002CQZ-110 | IC FRONT END 10BIT VID 128-MQFP |
| ISL5314IN | IC SYNTHESIZER DIGITAL 48-MQFP |
| ISL55100AIRZ-T | IC COMP DRVR/WINDOW 18V 72-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL36111 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:11.1Gb/s Lane Extender |
| ISL36111DRZ-EVALZ | 功能描述:EVAL BOARD FOR ISL36111DRZ RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
| ISL36111DRZ-T7 | 功能描述:IC EQUALIZER REC 11.1GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:QLx™ 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| ISL36111DRZ-TS | 功能描述:IC EQUALIZER REC 11.1GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:QLx™ 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| ISL36356A-APDK | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:PRISM 11Mbps Wireless Local Area Network Access Point |
发布紧急采购，3分钟左右您将得到回复。